PRODUCT DETAILS
Seibon OE-Style Carbon Fiber Hood - 1997-2001 Honda Prelude
Want the weight savings and the carbon look on your Prelude without slapping an aggressive aftermarket hood on that clean fifth-gen front end? This is exactly the one. The Seibon OE-Style carbon fiber hood copies your Prelude's factory hood shape, line for line, and remakes it in real carbon fiber. So you keep those smooth, low, unmistakably Prelude lines, but now they're carbon, lighter, glossier, and a whole lot cooler than the steel hood. It's the subtle move: all the upside of carbon, none of the try-hard.
Why OE-Style Is The Move
Here's what sets this apart. Plenty of carbon hoods go loud with vents and aggressive shapes, and that's fine if that's your build. But the OE-Style keeps the factory silhouette, so from a few feet away it reads stock, and up close you catch that deep carbon weave sitting under the gloss. It's understated and clean, which is perfect for a Prelude, a car that always had elegant lines to begin with. If you're building a tasteful OEM+ or restomod Prelude and want it to look factory-fresh but a step above, this is the look you want.
Real Weight Off That Long Nose
And there's a genuine functional payoff here. The Prelude is a front-engine coupe with a long hood, which means there's a good chunk of steel sitting way out over the front axle. Swap it for carbon and you're pulling real weight off the nose, right where it helps your balance and turn-in the most. Let's keep it honest, a hood alone won't transform the car, but on a nose-heavy front-driver like this, losing steel up front is one of the better places to shed weight, and you're getting the carbon look right along with it.
Bolts Right On
The install is easy because it's a 100% bolt-on. It's made to use all your factory hinges, latches, and windshield sprayers, so it goes on with the hardware already on your car, no cutting, no fabricating. Pull the steel hood, bolt this one up, carry your sprayers over, and you're finished.
Built To Last
Seibon finishes these with a high-gloss clear coat over a clean, consistent weave, and that clear coat is what fends off chipping and flaking so it holds its shine instead of going dull after a season. Seibon's been doing carbon body panels for well over a decade, and it shows in the weave and the finish. This is real carbon done the right way.
Hood Pins Recommended
Even though this hood bolts on with your factory hardware, it's smart to run a set of hood pins, especially if you drive the car hard or take it to the track. They lock the hood down for extra security at speed, so it's cheap peace of mind. Not strictly required, but a wise move if you're pushing the Prelude.
What You Get
- Seibon OE-Style carbon fiber hood for the 1997-2001 Honda Prelude
- Factory hood shape reproduced in real carbon fiber for a clean, subtle look
- Glossy clear-coat finish that resists chipping and flaking
- Lighter than the factory steel hood for weight savings over the front axle
- 100% bolt-on: accepts factory hinges, latches, and windshield sprayers
- Hood pins recommended (not included)
Fits These Cars
- 1997-2001 Honda Prelude (Base and Type SH)
Note: Seibon OE-Style carbon fiber hood for the 1997-2001 Honda Prelude. This hood reproduces the factory hood shape in carbon fiber for a clean, subtle OEM-style look, finished with a high-gloss clear coat that resists chipping and flaking, and is lighter than the steel hood for weight savings over the front axle, which is especially worthwhile on the Prelude's long front-engine nose. This is primarily a styling and weight upgrade. It is a 100% bolt-on that accepts all factory hinges, latches, and windshield sprayers. Hood pins are recommended for added security, especially for track or spirited driving, and are not included. Fits the 1997-2001 Honda Prelude, including Base and Type SH. One hood per order.