InlinePro Xtreme Duty Alloy Head Studs for B16A/B18C/LS VTEC

  • Holds the Head Down under Boost and Serious NA Builds

  • Resists Hydrogen Embrittlement, Unlike L19/H11

  • 230kpsi M11 Premium American Alloy

  • Covers VTEC and LS/VTEC Builds

$249.95

/
Subscription

Select an option to add this to your cart

Availability needs to be checked. See the message below. Currently out of stock Available to order In stock · available Available to order

Fitment: B16A

Part # ILP-HS-B16

Vehicle compatibility

Check compatibility with your vehicle.

Description

InlinePro Xtreme Duty Alloy Head Studs - B16A / B18C / LS VTEC

The B-series is the Honda engine everyone builds, and once you start adding power the factory head bolts become the limit. Combustion pressure pushes the head up off the block on every power stroke, and the stock torque-to-yield bolts only hold so much before the head lifts and the gasket gives up. That turns into coolant in the oil, oil in the coolant, or a lost cylinder between chambers. Head studs stop it. On a boosted B16, a built B18C, or an LS/VTEC making real power, they're one of the first upgrades the engine needs before you lean on it.

Why Studs Beat Factory Bolts

A torque-to-yield bolt is a one-time part. You torque it, it stretches past its yield point by design, and the hold you get is whatever's left when it stops stretching. Reuse one and it's weaker still. A stud works nothing like that. It threads into the block finger-tight with no load on it, and the nut on top does the actual clamping. You torque the nut to a real, repeatable number, the load spreads evenly across the head, and the head stays put under boost. Pull the engine apart down the road and the studs come right back out and go back in.

Built for Serious Clamp

These are M11 M-series studs machined from the highest-grade premium American alloy, heat treated and tested. With a 230,000 psi minimum tensile strength, they clamp far harder than the factory bolts ever could, which is exactly what a built B-series needs once it's making real cylinder pressure from boost or a high-compression setup.

No Hydrogen Embrittlement

A lot of high-strength studs on the market are made from L19 or H11. Strong material, but it comes with a catch: both are prone to hydrogen embrittlement. Leave them exposed to moisture, skip the oil, or handle them carelessly, and they can crack later on. This alloy doesn't carry that weakness. You can handle them, install them, and leave them in the engine without treating them like they might turn on you.

True-Beam Design

Plenty of competitor studs have a thinner section machined into the middle, necked down or undercut. These don't. The beam runs full diameter end to end. A full-diameter beam flexes less and puts more of your torque into holding the head down instead of into stretching the stud, which also keeps your torque readings honest when you tighten the nuts.

What's in the Kit

Studs, nuts, washers, assembly lube, and instructions. Everything the job takes, in the box.

Fitment

These head studs fit any B-series engine running a B16A or B18C VTEC cylinder head, which covers:

  • 1999-2000 Honda Civic Si (B16A2)
  • 1994-1997 Honda del Sol VTEC (B16A3)
  • 1997-2001 Acura Integra Type R (B18C5)
  • 1994-2001 Acura Integra GS-R (B18C)
  • 1994-2001 Acura Integra LS/GS/RS running a B16A or B18C head (LS/VTEC)

If you're building an LS/VTEC, these are the studs for the VTEC head on your LS bottom end.

Installation Notes

This is a job for when the head is off, during a gasket or head service. Spin each stud into the block by hand only, never torqued down into the block itself, and let the nuts up top do the work. Lube the threads and the underside of the nuts with what's in the kit, because dry threads throw off your torque wrench and leave the head under-clamped. Then work up to spec in stages, in the sequence the instructions give, and the head is clamped down for whatever the B-series throws at it.

FITMENT

1994-2001 Acura Integra
1999-2000 Honda Civic Si
1994-1997 Honda Del Sol VTEC

YOU MAY ALSO LIKE

RECENTLY VIEWED