Product images 1 / 1
Description
InlinePro L15B7 / L15CA 1.5T Xtreme Duty MLS Head Gasket
Honda's 1.5T has a head gasket reputation, and not a good one. The engine makes boost from the factory, so the gasket is already working harder than the one in a naturally aspirated motor. Then you add a tune and more airflow. Cylinder pressure climbs, and the factory gasket is usually the first thing to start complaining. It was built to seal a stock engine and nothing past that, which is fine until the day you ask it for more. This InlinePro Xtreme Duty gasket is the answer. It swaps that composite factory piece for three bonded layers of stainless steel, and the steel is the whole point. Each layer adds clamping strength and sealing surface, so the gasket keeps the combustion chambers, the coolant jackets, and the oil passages sealed when pressure and heat run well past stock. That's the exact point where the original starts to seep coolant, push oil, or let go between cylinders. Tuning one of these past stock power? The gasket is cheap insurance against a job you really don't want to do twice.
Choose the Variant for Your Car
There are two bore sizes, and this is the one detail you have to get right. Honda changed the bore slightly across the 1.5T's life, so the gasket has to match the engine you actually have:
- 73.5mm bore - 2016-2021 Honda Civic 1.5T (EX-T, Sport, Sport Touring) and 2017-2020 Civic Si. This is the tenth-gen L15B7.
- 73.0mm bore - 2018-2022 Honda Accord 1.5T, 2022-2027 Honda Civic 1.5T (Si, EX, Sport, Sport Touring), 2023-2027 Acura Integra (Base, A-Spec), and 2023-2027 Honda CR-V 1.5T. These share the later engine.
Thickness is the same 0.036" on both, so bore is the thing that changes. The gasket opening has to line up with the cylinder it seals, which is why the wrong bore won't do. Each bore also has a fitment-specific version beyond the size. If you're not certain which your car takes, check the engine code before you order. The chassis and engine tell you what you need, not the model year on its own.
Three-Layer MLS at 0.036"
Each gasket is a three-layer MLS build at a 0.036" compressed thickness. That number is fixed and known, so your compression and quench math stays simple when you're spec'ing a built motor. The construction is where it earns its money. A composite gasket is one soft layer that relies on getting crushed to seal, and it gives up as pressure climbs. Three layers of spring steel clamp down and hold, flexing with the engine instead of fighting it. That's what lets it take the cylinder pressure a tuned 1.5T makes and keep sealing where the single-layer factory gasket was never built to.
Installation Notes
MLS seals by clamping flat steel against flat metal, so surface prep matters more than it does with a composite gasket. Both the deck and the head have to be clean and genuinely flat, machined to the surface finish the steel needs to bite against. A composite gasket will forgive a rough or slightly uneven surface. An MLS gasket won't, so if there's any doubt about either surface, have it checked and resurfaced before you go back together. From there it's the usual care a boosted build deserves. Run good head studs, torque them in the correct sequence to spec, and confirm your final compression works with your fuel and tune. Done right, this gasket holds up to serious boost. Done on a warped deck or with uneven clamping load, no gasket is going to save the engine.
FITMENT
2023-2027 Acura Integra Base/ASpec
2018-2022 Honda Accord 1.5T
2016-2021 Honda Civic EX-T/Sport/Sport Touring
2017-2020 Honda Civic Si
2022-2027 Honda Civic EX/Sport/Sport Touring/Si
IN THE BOX
(1) Head Gasket