Product images 1 / 1
Description
InlinePro K-Series MLS Head Gasket - K20 & K24
The head gasket seals the combustion chambers along with the coolant and oil passages between the block and the cylinder head, and on a K-series that you're building for more power it tends to be one of the first parts to let go if it isn't up to the job, which is why it's worth not cutting corners on. This one is a multi-layer steel gasket, which just means it's made from several thin layers of stainless steel bonded together instead of the composite material the factory used, and that layered steel is what lets it keep sealing when cylinder pressures and temperatures climb well past stock, so once you've raised the compression or added boost or started spraying the motor it holds where a composite gasket would begin to give up and eventually blow out the moment the pressure in a cylinder spikes.
Choose the Bore Size to Match Your Block
This gasket comes in six bore sizes so you can match it to your engine's actual cylinder bore, which is the one selection you really need to get right on this page:
- 86mm
- 86.5mm
- 87mm
- 87.5mm
- 88mm
- 88.5mm
A stock K20 comes in at an 86mm bore and a stock K24 at 87mm, so if the engine hasn't been touched you just take the gasket that matches, but if the block has been bored out for a bigger set of pistons then you want the gasket size that clears whatever your final machined bore ended up being. The reason it matters is that the gasket opening has to sit just outside the cylinder wall, so you go with a bore size that's equal to or a touch larger than your pistons rather than anything smaller, because a gasket ring that hangs down into the cylinder isn't going to seal right and ends up in the way of the piston and ring pack as they come up the bore. The number you're working from, in other words, is whatever the block actually measures now that it's been machined, not what it displaced the day you bought it, which is an easy thing to lose track of if the boring happened a while ago.
0.030" Thickness
All six sizes share the same 0.030" thickness, and because that compressed thickness is a known, consistent figure you can fold it straight into your compression and quench math while you're spec'ing the build. With the thickness fixed across the whole range, the only thing you're actually choosing between on this page is bore size.
Fitment
This MLS head gasket fits the K20 and K24 engines, specifically the K20A2, K20A3, K20Z1, K20Z3, K24A1, K24A2, K24A4, and K24A8, as found in:
- 2002-2006 Acura RSX Base / Type-S
- 2004-2008 Acura TSX
- 2003-2007 Honda Accord
- 2002-2005 Honda Civic Si
- 2006-2011 Honda Civic Si
- 2002-2006 Honda CR-V
- 2003-2011 Honda Element
Confirm your final bore size before ordering so the gasket matches the block you actually have.
Installation Notes
An MLS gasket doesn't seal the same way a composite one does, and it's a good deal less forgiving of a rough or uneven surface, so before anything goes back together you want both the block deck and the head clean, flat, and machined to the surface finish the steel layers need to bite against, which in practice usually means having the deck resurfaced and checked for flatness if there's any doubt about it at all. From there it's the same care any serious K-series assembly deserves, running quality head studs and torquing them down in the right sequence to spec, and then checking that the compression ratio you end up with actually agrees with the fuel you plan to run and the tune behind it, since an MLS gasket will take a lot of abuse but only when the surfaces it's clamped between and the clamping load holding it there are both where they should be.
FITMENT
2002-2006 Acura RSX Base/Type S
2004-2008 Acura TSX
2003-2007 Honda Accord
2002-2005 Honda Civic Si
2006-2011 Honda Civic Si
2002-2006 Honda CR-V
2003-2011 Honda Element