InlinePro H22 Head Studs for 93-01 Honda Prelude

  • Holds the Head Down under Boost

  • Two Materials, Alloy or Super Alloy

  • Resists Hydrogen Embrittlement, Unlike L19/H11

  • Full True-Beam Design for Even Clamping

$349.95
 - $499.95

/
Subscription

Select an option to add this to your cart

Availability needs to be checked. See the message below. Currently out of stock Available to order In stock · available Available to order

Material: Alloy - Extreme Duty

Part # ILP-HS-H22

Vehicle compatibility

Check compatibility with your vehicle.

Description

InlinePro H22 Head Studs - 1993-2001 Honda Prelude

Boost an H22 and the factory head bolts become the weak link. Combustion pressure tries to shove the head off the block on every power stroke, and the stock torque-to-yield bolts only hold so much before the head lifts and the gasket lets go. Coolant in the oil, oil in the coolant, or a dead cylinder between two chambers. That's the failure these studs exist to prevent. The Prelude's H22 is one of the most swapped and boosted Honda engines out there, and head studs are one of the first things it needs before the power goes up.

Why Studs Beat Factory Bolts

A torque-to-yield bolt is a one-time part. You torque it, it stretches past its yield point on purpose, and whatever hold you get is whatever's left when it stops stretching. Reuse one and it's weaker still. A stud skips all of that. It threads into the block finger-tight, carrying no load at all, and the nut on top is what actually tightens the head down. You torque the nut to a real number you can hit again and again, the load spreads evenly across the head, and the head quits lifting under boost. Pull the engine apart a year later and the studs come out and go right back in.

Choose Your Material

Both are M12 M-series studs, cut from premium American stock, heat treated and tested in-house. What separates them is strength:

  • Alloy, Extreme Duty (230kpsi): the pick for a strong street car or a moderate-boost build. 230,000 psi minimum tensile is a huge jump over the factory bolts and handles the majority of built H22s.
  • Super Alloy, Xtreme Power (260kpsi): the pick when the boost and the power targets get serious. 260,000 psi buys you more headroom for a motor making big cylinder pressure.

Pick for where the build is going, not where it sits right now. Buying the super alloy up front costs less than tearing the engine down again to step up later.

No Hydrogen Embrittlement

Plenty of high-strength studs on the market are L19 or H11. Strong stuff, but it has a catch: both are prone to hydrogen embrittlement. Leave them exposed to moisture, skip the oil, handle them carelessly, and they can crack down the road. InlinePro's alloys don't carry that weakness. You can handle them, install them, and leave them in the engine without treating them like they might turn on you.

True-Beam Design

Look at a lot of competitor studs and you'll see a thinner section machined into the middle, necked down or undercut. These aren't. The beam runs full diameter end to end. A full-diameter beam flexes less and puts more of your torque into holding the head down instead of into stretching the stud, which also makes your torque readings more honest when you tighten the nuts.

What's in the Kit

Studs, nuts, washers, assembly lube, and instructions. Everything the job takes, in the box.

Fitment

Fits the H22 VTEC engine in the 1993-2001 Honda Prelude.

Installation Notes

This is a job for when the head is off, during a gasket or head service. Spin each stud into the block by hand only, never torqued into the block itself, and let the nuts up top do the work. Lube the threads and the underside of the nuts with what's in the kit, because dry threads lie to your torque wrench and leave the head under-clamped. Then work up to spec in stages, in the sequence the instructions give, and the head is locked down for whatever the H22 throws at it.

FITMENT

1992-1996 Honda Prelude
1997-2001 Honda Prelude

YOU MAY ALSO LIKE

RECENTLY VIEWED