Hybrid Racing Titanium Maxim Shift Boot Collar

  • Machined Titanium 

  • Stainless Steel Sleeve

  • Dust Titanium & Blue finish

  • Includes elastic retaining band

$87.99 $109.99 $109.99

/
Subscription

Select an option to add this to your cart

Availability needs to be checked. See the message below.
Delivery truck icon Ships in 3-6 Weeks
Delivery truck icon Ships in 3-6 Weeks
In stock · available
Available to order

Color: Titanium

Part # HYB-BCA-01-11

Vehicle compatibility

Check compatibility with your vehicle.

Description

Hybrid Racing Titanium Shift Boot Collar

Want to ditch the stock knob but can't stand the sad, saggy boot look? This fixes it. The Hybrid Racing shift boot collar is a clean two-piece setup that replaces the factory collar and works with a stock knob or just about any aftermarket knob you want to run, no hacky zip ties holding your boot in place.

How It Works

The stainless steel center section threads onto any M10x1.5 shifter rod, then clips into the titanium collar. That gives you a sleeve that actually holds the boot where it should sit, even after a few hot days in the car. Instead of an elastic band that stretches and slips over time, you get a secure mechanical hold that stays put.

Simple Install

Install is straightforward. The center section threads on, the collar clips in, and you only need a 17mm wrench to snug the sleeve up against any flat-bottom knob. That's the whole job.

About The Titanium Finish

The outer piece is machined titanium, which gives you that burnt-titanium look, anywhere from a dusty finish to a blue tone depending on the batch. That's the nature of the material, so we'll be straight with you about it.

Not all titanium parts have the same finish. Color can vary from part to part.

If you want a shift boot collar that looks the part and stays tight, this is it.

What You Get

  • Hybrid Racing two-piece titanium shift boot collar
  • Stainless steel center section, threads onto any M10x1.5 rod
  • Machined titanium outer collar
  • Works with a stock knob or most flat-bottom aftermarket knobs
  • Secure mechanical hold, no elastic band to slip
  • Installs with a 17mm wrench

SKU: HYB-BCA-01-11

INSTALL GUIDE
IN THE BOX

(1) Titanium shift boot collar
(1) Stainless steel sleeve
(1) Elastic rubber retaining band

Install guide

Hybrid Racing Maxim Shift Boot Collar Install Guide

Hybrid Racing Maxim Shift Boot Collar kit parts: black outer collar, stainless inner sleeve, and rubber band.
Cover photo showing the three pre-assembled parts of the Maxim Shift Boot Collar: outer collar, inner sleeve, and elastic band.
Difficulty
Easy
Steps
5
Time required
5 min – 10 min
Category
Interior3

Tools

  • Wrench
    Quantity: —

01 Parts of the shift boot collar

Black rubber band, stainless steel sleeve, and black anodized outer collar of the Hybrid Racing Maxim Shift Boot Collar.
The three parts: elastic rubber retaining band (left), stainless steel inner sleeve (center), and anodized aluminum outer collar (right).
  1. The Hybrid Racing Maxim Shift Boot Collar comes pre-assembled and contains 3 parts.
  2. The outer collar is made from anodized aluminum.
  3. The inner sleeve is machined from stainless steel.
  4. The elastic rubber retaining band holds the collar to your shift boot.

02 Installing the boot collar

Shift boot fabric with Hybrid Racing collar and elastic band at the metal sleeve end.
Look at the elastic band stretched around the fabric, securing the collar to the boot at the metal end.
Black elastic band securing gray fabric shift boot around the metal collar end.
Elastic band stretched around the fabric, securing it to the boot collar.
  1. Since this is a universal part, you will need to remove the shift boot from your console and remove the stock collar.
  2. Fold the shift boot inside out and slide the collar all the way in until it comes out the other end.
  3. Once you have the sleeve in place, stretch the elastic band around the fabric, securing it to the boot.
  4. noteYou should use the elastic band included with the collar kit. Some factory cars use thin zip-ties to secure the fabric but these are bulky and can wear the outside of the boot quickly.

03 Installing the collar

Black Hybrid Racing shift boot collar with red stitching around the shift rod, red arrow pointing down.
Slide the boot and collar down onto the shift rod after removing the inner sleeve.
Stainless steel sleeve threaded onto the shift rod above the Hybrid Racing shift boot collar.
Stainless steel sleeve threaded onto the shift rod after sliding the boot and collar down.
Hybrid Racing shift boot collar on the shift rod with stainless sleeve above and upward arrow
Slide the collar up the shift rod until it clips into place against the stainless steel sleeve.
  1. After you have the boot collar secured to the fabric, remove the inner sleeve from the collar. Slide the boot and collar down onto the shift rod.
  2. Thread the stainless steel sleeve onto the rod.
  3. Once you have your shift knob threaded on, use a wrench to tighten the stainless steel sleeve against the knob, locking it into place.
  4. Slide the collar up and it will clip into place.

04 Installing the collar

Black Hybrid Racing shift boot collar standing alone, showing the top opening and threaded center.
The Hybrid Racing Maxim shift boot collar, ready to install with its dual-height settings for OEM or aftermarket knobs.
Silver spherical shift knob with red pattern seated on Hybrid Racing collar above black leather shift boot.
Collar slid up under the installed shift knob, clicking into place to close the gap for an OEM finish.
Hybrid Racing collar seated at the base of a silver spherical shift knob on the black shift boot.
Red arrows show the collar slid up and clicked into place against the shift knob for a clean OEM-style finish.
  1. One unique feature of our boot collar is that is has two settings which can work with a variety of shift knobs.
  2. If you prefer to use the OEM Honda knobs, our boot will clip up to conceal the lower lip. (OEM FK8 Type-R Knob Shown)
  3. Install the shift knob and position it to your liking. Use a wrench and tighten the sleeve against the collar.
  4. Slide the collar up and it will click into place closing the gap for a nice OEM finish.

05 Enjoy!

Hybrid Racing Maxim shift boot collar seated atop the black shift boot in the Civic Type R center console.
Completed install: the Maxim shift boot collar sits on the fabric boot, ready for any shift knob.
Hybrid Racing Maxim shift boot collar fitted at the base of a brushed metal shift knob on a black leather boot.
Finished install of the Maxim shift boot collar locking the fabric boot to the shift knob.
Red Hybrid Racing shift knob with Maxim collar seated on black leather shift boot.
Completed install: Maxim shift boot collar locking the red knob to the black fabric boot.
  1. This adaptable shift boot collar is a universal part that works with any fabric shift boot and any shift knob!
  2. Enjoy!

Finishing up

After locking the stainless sleeve and clipping the collar in place, enjoy your adaptable Hybrid Racing Maxim Shift Boot Collar, a universal part that works with any fabric shift boot and any shift knob.

Revision 3 · Updated Nov 12, 2026

YOU MAY ALSO LIKE

RECENTLY VIEWED