{"product_id":"whiteline-control-arm-lower-rear-inner-and-outer-bushing-for-acura-and-honda","title":"Whiteline Rear Lower Control Arm Bushings for Honda\/Acura","description":"\u003cul\u003e\n\u003cli\u003ePrecision engineered for your vehicle \u003c\/li\u003e\n\u003cli\u003eMade from premium materials for long-lasting durability \u003c\/li\u003e\n\u003cli\u003eImproves vehicle handling \u003c\/li\u003e\n\u003cli\u003eTested to outperform comparable products \u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003c!-- split --\u003e\n\u003cul class=\"tabs\"\u003e\n\u003cli\u003e\u003ca class=\"active\" href=\"#Description\"\u003eDescription\u003c\/a\u003e\u003c\/li\u003e\n \u003cli\u003e\u003ca href=\"#VehicleFitment\"\u003eVehicle Fitment\u003c\/a\u003e\u003c\/li\u003e  \u003cli\u003e\u003ca href=\"#TechnicalData\"\u003eTechnical Data\u003c\/a\u003e\u003c\/li\u003e  \u003cli\u003e\u003ca href=\"#InstallGuide\"\u003eInstall Guide\u003c\/a\u003e\u003c\/li\u003e \u003c\/ul\u003e\n\u003cul class=\"tabs-content\"\u003e\n\n\n\u003cli class=\"active\" id=\"Description\"\u003e\n\u003ch3\u003eWhiteline Rear Lower Control Arm Bushings for Honda\/Acura \u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eWhiteline Rear Lower Control Arm Bushing \u003c\/strong\u003ekit is a rear lower control arm bushing kit that replaces the lower rear inner and lower rear outer pivot bushings on the rear suspension of specific Honda and Acura platforms. These bushings locate the rear lower control arm at the chassis and knuckle side pivots, controlling how the arm rotates through bump and rebound while resisting unwanted compliance under braking, acceleration, and cornering loads. When the original rear lower control arm bushings wear or crack, the arm can shift under load instead of rotating only around its intended pivot axis. That additional compliance can contribute to inconsistent rear wheel behavior and can accelerate tire wear or make alignment settings less stable over time. This kit is intended as a service replacement for those pivot points rather than a geometry correction part. This kit uses Whiteline synthetic elastomer bushings in place of the factory rubber pieces. The kit is sold as a matched set for the lower rear inner and outer locations on the rear lower control arm, and is application specific to the vehicles listed below. Published dimensional data for the kit includes a 31 millimeter outer diameter for one bushing position, which is relevant for confirming press fit compatibility with the original arm bore.\u003c\/p\u003e\n\n\n\n\n\n\u003ch4\u003eWhen an enthusiast or installer would choose it\u003cbr\u003e\n\u003c\/h4\u003e\n\u003cp\u003eThis kit is typically selected when refreshing an older rear suspension while retaining the factory control arms, especially when the goal is restoring consistent arm location at the pivots with a non OEM bushing material. It can also be appropriate when replacing bushings during other rear suspension service that already requires arm removal, such as damper or knuckle adjacent work, to avoid duplicating labor later.\u003c\/p\u003e\n\n\u003ch4\u003eInstallation and service considerations\u003cbr\u003e\n\u003c\/h4\u003e\n\u003cp\u003eThese are press fit style bushings that normally require bushing removal and installation tooling suitable for suspension bushings. Because the bushings locate the control arm pivots, alignment should be checked after installation if the arm position was disturbed during service. Verify whether your vehicle uses the specific rear lower control arm construction noted in the compatibility list, since listings for this part are commonly qualified by arm type and may include additional related bushings depending on the application note.\u003c\/p\u003e\n\u003ch4\u003eKey Features\u003c\/h4\u003e\n\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer part number\u003c\/strong\u003e: W62005\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eKit position\u003c\/strong\u003e: rear lower control arm, lower rear inner and lower rear outer bushing locations\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eBushing material\u003c\/strong\u003e: synthetic elastomer\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePublished bushing outer diameter\u003c\/strong\u003e: 31 millimeters\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVerified applications\u003c\/strong\u003e: 1994 to 2001 Acura Integra, 1988 to 2000 Honda Civic, 1988 to 1991 Honda CRX\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\n\u003c\/li\u003e\n\n \n\u003cli id=\"VehicleFitment\"\u003e\n    1997 - 2001 Acura Integra GS   1994 - 2001 Acura Integra GS-R   1994 - 2001 Acura Integra LS   1994 - 1998 Acura Integra RS   1988 - 2000 Honda Civic DX   1989 - 2000 Honda Civic Si   1989 - 1991 Honda CRX \n\u003c\/li\u003e\n\n\n\n\n\u003cli id=\"TechnicalData\"\u003e\nMaterial: Synthetic elastomer\n\u003c\/li\u003e\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\u003cli id=\"InstallGuide\"\u003e\nFollow the manufacturer's installation instructions carefully. Ensure all mounting points are clean and free from debris before installation. Use appropriate tools and techniques to avoid damage to the bushings or vehicle components.\n\u003c\/li\u003e\n\n\n\u003c\/ul\u003e\n","brand":"Whiteline","offers":[{"title":"Default Title","offer_id":69523955351586,"sku":"WYT-W62005","price":50.16,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/2218\/5701\/files\/WYT-W62005_1.jpg?v=1793308788","url":"https:\/\/www.hybrid-racing.com\/products\/whiteline-control-arm-lower-rear-inner-and-outer-bushing-for-acura-and-honda","provider":"Hybrid Racing","version":"1.0","type":"link"}