{"product_id":"skunk2-racing-10an-valve-cover-vent-kit-for-acura-rsx-type-s-honda-civic-si-1","title":"Skunk2 Racing -10AN Valve Cover Vent Kit for RSX \u0026 Civic Si","description":"\u003cul\u003e\n\u003cli\u003eDirect fit for Skunk2 Ultra Lightweight Magnesium Valve Cover \u003c\/li\u003e\n\u003cli\u003eFacilitates Connection to -10 AN External Breather Systems \u003c\/li\u003e\n\u003cli\u003eStainless Mesh Pre-Filters Included \u003c\/li\u003e\n\u003cli\u003eBolt-On Installation for Easy and Efficient Engine Vent Upgrade \u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003c!-- split --\u003e\n\u003cul class=\"tabs\"\u003e\n\u003cli\u003e\u003ca class=\"active\" href=\"#Description\"\u003eDescription\u003c\/a\u003e\u003c\/li\u003e\n \u003cli\u003e\u003ca href=\"#VehicleFitment\"\u003eVehicle Fitment\u003c\/a\u003e\u003c\/li\u003e  \u003cli\u003e\u003ca href=\"#TechnicalData\"\u003eTechnical Data\u003c\/a\u003e\u003c\/li\u003e   \u003cli\u003e\u003ca href=\"#Included\"\u003eIncluded\u003c\/a\u003e\u003c\/li\u003e  \u003cli\u003e\u003ca href=\"#InstallGuide\"\u003eInstall Guide\u003c\/a\u003e\u003c\/li\u003e \u003c\/ul\u003e\n\u003cul class=\"tabs-content\"\u003e\n\n\n\u003cli class=\"active\" id=\"Description\"\u003e\n\u003ch3\u003eSkunk2 -10AN Valve Cover Vent Kit - K Series (K20 \/ K24)\u003c\/h3\u003e\n\n\u003cp\u003e\n  Built a K-series and you're ready to plumb a real breather or catch can setup? This is how you do it\n  clean. The Skunk2 -10AN valve cover vent kit gives your K20 or K24 two big -10AN ports right in the valve\n  cover, so you can run -10AN lines straight to an external breather, oil separator, or catch can without\n  hacking together fittings that don't fit. It's a straight bolt-on, two fittings thread right in, and your\n  crankcase ventilation is sorted. If you're chasing more power and your engine's making more blow-by than\n  the stock PCV setup wants to handle, this is the upgrade that keeps your crankcase pressure under control\n  and your intake clean.\n\u003c\/p\u003e\n\n\u003ch4\u003eWhy You Vent The Valve Cover On A Built K-Series\u003c\/h4\u003e\n\u003cp\u003e\n  Here's what's going on inside your motor. The harder you push a K-series, especially once you're spinning\n  it to high RPM or adding boost, the more pressure and oil mist builds up in the crankcase from blow-by\n  past the rings. That pressure has to go somewhere, and if you leave it on a stock PCV system, a lot of\n  that oily air gets pulled right back into your intake, gunking up your manifold and throttle body and\n  costing you consistency. Venting the valve cover to an external breather or catch can gives that pressure\n  a clean way out and keeps the oil out of your intake tract. This kit is the plumbing that makes it\n  happen, two -10AN ORB to -10AN fittings that thread directly into your valve cover, sized big enough to\n  actually flow the volume a serious build puts out.\n\u003c\/p\u003e\n\n\u003ch4\u003eStainless Mesh Pre-Filters Keep Oil Out Of Your Breather\u003c\/h4\u003e\n\u003cp\u003e\n  The kit comes with two stainless steel mesh filter inserts, one for each fitting, and they're doing real\n  work. They sit in the fittings as pre-filters and catch oil mist on its way out, so less oil makes it\n  into your breather system or catch can. That means you're not constantly emptying an oil-soaked catch can,\n  you're burning less oil, and your whole ventilation setup stays cleaner and works better. It's a small\n  detail that makes a real difference in how often you're out there dealing with the mess.\n\u003c\/p\u003e\n\n\u003ch4\u003eMade For The Skunk2 Magnesium Valve Cover\u003c\/h4\u003e\n\u003cp\u003e\n  One important thing before you buy: this vent kit is built to thread into the \u003ca href=\"https:\/\/www.hybrid-racing.com\/products\/skunk2-racing-k-series-ultra-lightweight-magnesium-valve-cover-for-acura-rsx-type-s-honda-civic-si?_pos=1\u0026amp;_sid=4267bebe5\u0026amp;_ss=r\" target=\"_blank\"\u003eSkunk2 Ultra Lightweight Magnesium Valve Cover\u003c\/a\u003e for K series. That cover has the -10 ORB bungs these fittings screw into, so this\n  kit and that valve cover are designed to work together as a pair. If you've already got the Skunk2\n  magnesium valve cover on your RSX, Civic Si, or other K-swapped build, this is the kit that finishes off\n  your breather plumbing. If you don't have that cover yet, plan to grab it alongside this so you've got\n  somewhere to thread these fittings.\n\u003c\/p\u003e\n\n\u003ch4\u003eWho This Is For\u003c\/h4\u003e\n\u003cp\u003e\n  This is aimed at the K-series crowd running a real breather or catch can setup, high-RPM naturally\n  aspirated builds, boosted K20s and K24s, and track cars that need to manage crankcase pressure properly.\n  If you're plumbing an external oil separator or catch can with -10AN lines, this kit is the connection\n  between your valve cover and that system. For a mostly stock daily, you probably don't need it, but for a\n  built motor that's moving real air, this is how you ventilate it right.\n\u003c\/p\u003e\n\n\u003ch4\u003eWhat You Get\u003c\/h4\u003e\n\u003cul\u003e\n  \u003cli\u003eSkunk2 -10AN valve cover vent kit for K series (K20 \/ K24) engines\u003c\/li\u003e\n  \u003cli\u003eTwo -10 ORB to -10AN fittings that thread directly into the valve cover\u003c\/li\u003e\n  \u003cli\u003eTwo stainless steel mesh pre-filter inserts (one per fitting) to reduce oil blow-by\u003c\/li\u003e\n  \u003cli\u003eWorks with any external breather, oil separator, or catch can using -10AN plumbing\u003c\/li\u003e\n  \u003cli\u003eDesigned for the Skunk2 Ultra Lightweight Magnesium Valve Cover for K series\u003c\/li\u003e\n  \u003cli\u003eStraight bolt-on installation\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch4\u003eCompatible With\u003c\/h4\u003e\n\u003cul\u003e\n  \u003cli\u003eSkunk2 Ultra Lightweight Magnesium Valve Cover for K series (K20 \/ K24)\u003c\/li\u003e\n  \u003cli\u003eExternal breather, oil separator, and catch can systems using -10AN plumbing\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003e\n  Note: Skunk2 -10AN valve cover vent kit for Honda\/Acura K series (K20 and K24) engines. Includes two -10\n  ORB to -10AN fittings that thread directly into the valve cover and two stainless steel mesh pre-filter\n  inserts (one per fitting) that act as pre-filters to reduce oil blow-by and keep oil out of your external\n  breather system, lowering oil consumption. Lets you plumb the valve cover to any external breather, oil\n  separator, or catch can that uses -10AN lines for proper crankcase ventilation on high-RPM and boosted\n  builds. This kit is designed for the Skunk2 Ultra Lightweight Magnesium Valve Cover for K series, which\n  provides the -10 ORB bungs the fittings thread into, so that valve cover is required. Straight bolt-on\n  installation. One vent kit per order.\n\u003c\/p\u003e\n\u003c\/li\u003e\n\n \n\u003cli id=\"VehicleFitment\"\u003e\n    2002-2006 Acura RSX\u003cdiv\u003e2004-2008 Acura TSX\u003c\/div\u003e\n\u003cdiv\u003e2003-2007 Honda Accord\u003cbr\u003e\u003cdiv\u003e2002-2005 Honda Civic Si\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv\u003e2006-2011 Honda Civic Si\u003c\/div\u003e\n\u003cdiv\u003e2002-2006 Honda CR-V\u003c\/div\u003e\n\u003cdiv\u003e2003-2011 Honda Element\u003c\/div\u003e \n\u003c\/li\u003e\n\n\n\n\n\u003cli id=\"TechnicalData\"\u003e\nFittings: -10 ORB to -10 AN\u003cdiv\u003eCompatibility: Skunk2 Ultra Lightweight Magnesium Valve Cover\u003c\/div\u003e\n\u003cdiv\u003ePre-Filters: Stainless Steel Mesh\u003c\/div\u003e\n\u003c\/li\u003e\n\n\n\n \n\u003cli id=\"Included\"\u003e\n(2) -10AN Fittings\u003cdiv\u003e(2) O-Rings \u003c\/div\u003e\n\u003cdiv\u003e(2) Steel Mesh Pre-Filters   \u003c\/div\u003e\n\u003c\/li\u003e\n\n\n\n\n\n\n\n\n\n\n\n\u003cli id=\"InstallGuide\"\u003e\nInstallation is straightforward, designed for direct fitment with included components. Professional installation is recommended to ensure optimal performance and fitment.\n\u003c\/li\u003e\n\n\n\u003c\/ul\u003e\n","brand":"Skunk2 Racing","offers":[{"title":"Default Title","offer_id":45842698666018,"sku":"SK2-666-05-0300","price":26.25,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/2218\/5701\/files\/OvVaIT47tPadaPBCNiP_008_Product_processed.png?v=1782338759","url":"https:\/\/www.hybrid-racing.com\/products\/skunk2-racing-10an-valve-cover-vent-kit-for-acura-rsx-type-s-honda-civic-si-1","provider":"Hybrid Racing","version":"1.0","type":"link"}