{"product_id":"mishimoto-fluid-extractor-manual-pneumatic-5-6l","title":"Mishimoto Universal 5.6L Pneumatic Fluid Extractor","description":"\u003cul\u003e\n\u003cli\u003eManual and Pneumatic Extraction Modes \u003c\/li\u003e\n\u003cli\u003e Easy Fluid Changes \u003c\/li\u003e\n\u003cli\u003eWorks for Engine Oil, Brake Fluid, \u0026amp; Coolant \u003c\/li\u003e\n\u003cli\u003eValuable Tool to Add to Your Garage \u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003c!-- split --\u003e\n\u003cul class=\"tabs\"\u003e\n\u003cli\u003e\u003ca class=\"active\" href=\"#Description\"\u003eDescription\u003c\/a\u003e\u003c\/li\u003e\n \u003cli\u003e\u003ca href=\"#VehicleFitment\"\u003eVehicle Fitment\u003c\/a\u003e\u003c\/li\u003e   \u003cli\u003e\u003ca href=\"#Included\"\u003eIncluded\u003c\/a\u003e\u003c\/li\u003e \u003c\/ul\u003e\n\u003cul class=\"tabs-content\"\u003e\n\n\n\u003cli class=\"active\" id=\"Description\"\u003e\n\u003ch3\u003eMishimoto 5.6L Fluid Extractor - Manual and Pneumatic (MMTL-FEX-MP56)\u003c\/h3\u003e\n\n\u003cp\u003e\n  If you've built your K-swap, B-swap, or H22 project in a driveway, an apartment garage, or anywhere\n  without a lift, you already know the dance. Jack the car up, slide the stands under, crawl on your back\n  with a drain pan, hope the oil doesn't run down your sleeve, fight the drain plug you torqued a little\n  too hard last time, then find out your crush washer's the wrong size. A 20-minute fluid change turns\n  into an hour, all because the access geometry isn't on your side. This is the shortcut. Drop the tube\n  down your dipstick, pump the fluid up into the 5.6 liter canister, dump it in your recycle jug, done. No\n  jack stands, no oil on the concrete, no skinned knuckles.\n\u003c\/p\u003e\n\n\u003ch4\u003eWhat It Actually Does\u003c\/h4\u003e\n\u003cp\u003e\n  The Mishimoto MMTL-FEX-MP56 is a 5.6 liter (1.5 gallon) sealed canister with a vacuum pump that pulls\n  low-viscosity fluid up through a long, flexible draw straw. You can run it two ways: manual hand pump\n  when you're in a driveway or anywhere shop air isn't handy, or pneumatic mode that hooks to your\n  compressor and does the work hands-off. Pneumatic's faster since the compressor's doing the pumping, but\n  the manual mode means the tool isn't dead weight the second you're away from an air line. It handles\n  engine oil, automatic transmission fluid, coolant, power steering fluid, and brake fluid, so it's not a\n  one-trick oil-change tool.\n\u003c\/p\u003e\n\n\u003ch4\u003eThe Bleeder Adapter Is The Sleeper Feature\u003c\/h4\u003e\n\u003cp\u003e\n  Here's the part that makes this more than an oil sucker: the kit includes a bleeder screw adapter, and\n  that's what turns it into a full fluid maintenance tool. Pop the bleeder screw on a brake caliper, thread\n  the adapter on, and the extractor pulls a full brake bleed through suction, no helper pumping the pedal,\n  no pressure bottle. Same deal for bleeding the clutch on a hydraulic-clutch car. If you've ever tried to\n  bleed brakes solo and ended up yelling \"down... up... hold!\" through a cracked window, you'll appreciate\n  what this does.\n\u003c\/p\u003e\n\n\u003ch4\u003eWhy It Works So Well On A Honda\u003c\/h4\u003e\n\u003cp\u003e\n  This is where the extractor really shines on the cars you're probably working on. K-series, B-series,\n  D-series, and H-series engines all run straight-shot dipstick tubes that route right down to the oil pan\n  with barely any curve. The 7mm straw slides down a typical Honda dipstick tube and reaches the bottom of\n  the pan, so you actually pull most of the oil out. People always ask whether an extractor leaves a\n  meaningful amount behind, and on Honda dipstick geometry, the honest answer is no, not on any of these\n  engines. You're getting a real, complete oil change, not a half-measure.\n\u003c\/p\u003e\n\n\u003ch4\u003eKnow Its Limits\u003c\/h4\u003e\n\u003cp\u003e\n  Be straight about what this tool is for: low-viscosity fluids only. Don't try to pull gear oil out of a\n  diff, manual transmission fluid (most of it's too thick at room temp), or anything that's been sitting\n  cold and turned to syrup. The pump just can't move fluid that thick. And warm your engine up to\n  operating temp before you extract oil, since warm oil flows the way the pump needs it to. For the really\n  thick stuff, you're back under the car with a drain plug, that's just how it goes.\n\u003c\/p\u003e\n\n\u003ch4\u003eSpecs\u003c\/h4\u003e\n\u003cul\u003e\n  \u003cli\u003eManufacturer: Mishimoto\u003c\/li\u003e\n  \u003cli\u003ePart number: MMTL-FEX-MP56\u003c\/li\u003e\n  \u003cli\u003eCapacity: 5.6 liters (1.5 gallons)\u003c\/li\u003e\n  \u003cli\u003eOperation: manual hand pump and pneumatic (shop air)\u003c\/li\u003e\n  \u003cli\u003eRecommended air pressure: 85 psi\u003c\/li\u003e\n  \u003cli\u003eMaximum air pressure: 120 psi\u003c\/li\u003e\n  \u003cli\u003eCompatible fluids: engine oil, ATF, coolant, power steering fluid, brake fluid\u003c\/li\u003e\n  \u003cli\u003eAutomatic float shutoff to prevent overfill\u003c\/li\u003e\n  \u003cli\u003eRemovable lid for clean disposal and recycling\u003c\/li\u003e\n  \u003cli\u003eMishimoto Lifetime Warranty\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch4\u003eIs 5.6 Liters The Right Size For You?\u003c\/h4\u003e\n\u003cp\u003e\n  For a single Honda or Acura engine oil change, 5.6 liters is plenty with room to spare. A K20A2 holds\n  about 4.4 quarts (4.2L), a K24A about 4.6 quarts (4.4L), a B18C about 4.3 quarts (4.1L), and an H22A4\n  about 4.3 quarts (4.1L), so every one of them fits in the canister with margin left over. The only time\n  you'd want the bigger 9.5L MMTL-FEX-MP95 instead is if you're knocking out back-to-back oil changes on\n  multiple cars without dumping in between, or flushing a coolant system that holds 7+ liters, which is\n  unusual for these chassis. For a one-car driveway or apartment-garage routine, the 5.6L is the right\n  size, and the price reflects that.\n\u003c\/p\u003e\n\n\u003ch4\u003eWarm It Up First, Then Extract\u003c\/h4\u003e\n\u003cp\u003e\n  This one tip makes a real difference. Cold oil is roughly twice as thick as oil at operating temp, and\n  you'll feel that in how slow the pump pulls. So run the car for 5 to 10 minutes to bring the oil temp\n  up, shut it off, then let it sit a minute or two so the oil drains back down to the pan before you\n  extract. Don't go yanking it right after a long highway run either, when the oil's hot and sloshing\n  around you'll get inconsistent levels. A few minutes of patience gets you a clean, complete pull.\n\u003c\/p\u003e\n\n\u003ch4\u003eBleeding Brakes By Yourself\u003c\/h4\u003e\n\u003cp\u003e\n  The bleeder adapter is what makes this genuinely useful for brake service. Most home brake bleeds need\n  either a buddy pumping the pedal or a pressure-fed bottle, but this pulls the fluid out right at the\n  caliper through suction, so one person does a full four-corner bleed with no coordination at all. Your\n  sequence is still the usual right rear, left rear, right front, left front (longest lines first) on most\n  front-engine cars, and you've still got to keep the master cylinder topped off so you don't suck air\n  back in. Same procedure as always, the extractor just makes it faster and a whole lot cleaner.\n\u003c\/p\u003e\n\n\u003ch4\u003eRecycle The Old Fluid The Right Way\u003c\/h4\u003e\n\u003cp\u003e\n  Quick reminder: most auto parts stores take used motor oil and coolant for free or close to it, and the\n  removable lid on this canister makes pouring it into a recycle jug clean and direct. Don't dump it on the\n  ground, don't toss it in your trash. The whole point of a tool that keeps your floor clean is wasted if\n  the old fluid ends up somewhere it shouldn't.\n\u003c\/p\u003e\n\n\u003ch4\u003eThe Lifetime Warranty Is The Real Deal\u003c\/h4\u003e\n\u003cp\u003e\n  Mishimoto's lifetime warranty actually means something. On the rare occasion we've sent a customer back\n  to Mishimoto on a warranty case across their product line, they've handled it cleanly, no runaround. For\n  a tool you'll own for the next decade-plus of fluid changes, that's the kind of warranty that matters.\n  Buy it once, use it on every oil change you do for the next ten years, and you've spent less per change\n  than the dealer charges for a single one.\n\u003c\/p\u003e\n\n\u003ch4\u003eWhat You Get\u003c\/h4\u003e\n\u003cul\u003e\n  \u003cli\u003eMishimoto 5.6L (1.5 gallon) fluid extractor (MMTL-FEX-MP56)\u003c\/li\u003e\n  \u003cli\u003eManual hand pump and pneumatic (shop air) operation\u003c\/li\u003e\n  \u003cli\u003eLong flexible draw straw (7mm) for Honda\/Acura dipstick tubes\u003c\/li\u003e\n  \u003cli\u003eBleeder screw adapter for solo brake and clutch bleeding\u003c\/li\u003e\n  \u003cli\u003eAutomatic float shutoff and removable lid for clean disposal\u003c\/li\u003e\n  \u003cli\u003eWorks with engine oil, ATF, coolant, power steering fluid, and brake fluid\u003c\/li\u003e\n  \u003cli\u003eBacked by Mishimoto's Lifetime Warranty\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003e\n  Note: Mishimoto fluid extractor, part number MMTL-FEX-MP56, a 5.6 liter (1.5 gallon) sealed canister\n  with a vacuum pump and a long flexible 7mm draw straw. Runs in manual hand pump mode or pneumatic mode\n  off shop air (85 psi recommended, 120 psi maximum). Extracts low-viscosity fluids only, including engine\n  oil, ATF, coolant, power steering fluid, and brake fluid; it is not for gear oil, most manual\n  transmission fluid, or any thick or cold fluid. Warm the engine to operating temperature before\n  extracting oil. Includes a bleeder screw adapter for one-person brake and hydraulic clutch bleeding, an\n  automatic float shutoff to prevent overfill, and a removable lid for clean disposal. The 5.6L capacity\n  covers a full single-engine Honda or Acura oil change with margin; for back-to-back changes or large\n  coolant flushes, see the 9.5L MMTL-FEX-MP95. Backed by Mishimoto's Lifetime Warranty. One extractor per\n  order.\n\u003c\/p\u003e\n\u003c\/li\u003e\n\n \n\u003cli id=\"VehicleFitment\"\u003e\n Universal \n\u003c\/li\u003e\n\n\n\n\n\n\n \n\u003cli id=\"Included\"\u003e\n\u003ctable\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eItem\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cstrong\u003eUse\u003c\/strong\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e5.6L fluid extractor canister\u003c\/td\u003e\n\u003ctd\u003eThe pump and reservoir\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAdapter hose\u003c\/td\u003e\n\u003ctd\u003eConnects pump output to draw straw or bleeder adapter\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2mm draw straw (4 ft)\u003c\/td\u003e\n\u003ctd\u003eSmallest tubes, narrowest dipstick passages, brake fluid lines\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e4mm draw straw (4 ft)\u003c\/td\u003e\n\u003ctd\u003eMid-sized tubes, smaller power steering reservoirs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e6mm draw straw (4 ft)\u003c\/td\u003e\n\u003ctd\u003eStandard car dipstick tubes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e7mm draw straw (4 ft)\u003c\/td\u003e\n\u003ctd\u003eLarger dipstick tubes, faster engine oil extraction\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBleeder screw adapter\u003c\/td\u003e\n\u003ctd\u003eThreads onto brake or clutch bleeder screws for hands-free bleeding\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAir fitting\u003c\/td\u003e\n\u003ctd\u003eConnects canister to standard shop air quick-connect\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\u003c\/li\u003e\n\n\n\n\n\n\n\n\n\n\n\n\n\u003c\/ul\u003e\n","brand":"Mishimoto","offers":[{"title":"Default Title","offer_id":45841245732898,"sku":"MIS-MMTL-FEX-MP56","price":112.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/2218\/5701\/files\/Ovkea-lnqvjQ0Flv5ip_007_S_-_P1_processed.png?v=1782317187","url":"https:\/\/www.hybrid-racing.com\/products\/mishimoto-fluid-extractor-manual-pneumatic-5-6l","provider":"Hybrid Racing","version":"1.0","type":"link"}