{"product_id":"inline-pro-h22-head-studs-honda-prelude","title":"InlinePro H22 Head Studs for 93-01 Honda Prelude","description":"\u003cul\u003e\n\u003cli\u003eHolds the Head Down under Boost \u003c\/li\u003e\n\u003cli\u003eTwo Materials, Alloy or Super Alloy \u003c\/li\u003e\n\u003cli\u003eResists Hydrogen Embrittlement, Unlike L19\/H11 \u003c\/li\u003e\n\u003cli\u003eFull True-Beam Design for Even Clamping \u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003c!-- split --\u003e\n\u003cul class=\"tabs\"\u003e\n\u003cli\u003e\u003ca class=\"active\" href=\"#Description\"\u003eDescription\u003c\/a\u003e\u003c\/li\u003e\n \u003cli\u003e\u003ca href=\"#VehicleFitment\"\u003eVehicle Fitment\u003c\/a\u003e\u003c\/li\u003e \u003c\/ul\u003e\n\u003cul class=\"tabs-content\"\u003e\n\n\n\u003cli class=\"active\" id=\"Description\"\u003e\n\u003ch3\u003eInlinePro H22 Head Studs - 1993-2001 Honda Prelude\u003c\/h3\u003e\n\n\u003cp\u003eBoost an H22 and the factory head bolts become the weak link. Combustion pressure tries to shove the head off the block on every power stroke, and the stock torque-to-yield bolts only hold so much before the head lifts and the gasket lets go. Coolant in the oil, oil in the coolant, or a dead cylinder between two chambers. That's the failure these studs exist to prevent. The Prelude's H22 is one of the most swapped and boosted Honda engines out there, and head studs are one of the first things it needs before the power goes up.\u003c\/p\u003e\n\n\u003ch4\u003eWhy Studs Beat Factory Bolts\u003c\/h4\u003e\n\n\u003cp\u003eA torque-to-yield bolt is a one-time part. You torque it, it stretches past its yield point on purpose, and whatever hold you get is whatever's left when it stops stretching. Reuse one and it's weaker still. A stud skips all of that. It threads into the block finger-tight, carrying no load at all, and the nut on top is what actually tightens the head down. You torque the nut to a real number you can hit again and again, the load spreads evenly across the head, and the head quits lifting under boost. Pull the engine apart a year later and the studs come out and go right back in.\u003c\/p\u003e\n\n\u003ch4\u003eChoose Your Material\u003c\/h4\u003e\n\n\u003cp\u003eBoth are M12 M-series studs, cut from premium American stock, heat treated and tested in-house. What separates them is strength:\u003c\/p\u003e\n\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlloy, Extreme Duty (230kpsi):\u003c\/strong\u003e the pick for a strong street car or a moderate-boost build. 230,000 psi minimum tensile is a huge jump over the factory bolts and handles the majority of built H22s.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSuper Alloy, Xtreme Power (260kpsi):\u003c\/strong\u003e the pick when the boost and the power targets get serious. 260,000 psi buys you more headroom for a motor making big cylinder pressure.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003ePick for where the build is going, not where it sits right now. Buying the super alloy up front costs less than tearing the engine down again to step up later.\u003c\/p\u003e\n\n\u003ch4\u003eNo Hydrogen Embrittlement\u003c\/h4\u003e\n\n\u003cp\u003ePlenty of high-strength studs on the market are L19 or H11. Strong stuff, but it has a catch: both are prone to hydrogen embrittlement. Leave them exposed to moisture, skip the oil, handle them carelessly, and they can crack down the road. InlinePro's alloys don't carry that weakness. You can handle them, install them, and leave them in the engine without treating them like they might turn on you.\u003c\/p\u003e\n\n\u003ch4\u003eTrue-Beam Design\u003c\/h4\u003e\n\n\u003cp\u003eLook at a lot of competitor studs and you'll see a thinner section machined into the middle, necked down or undercut. These aren't. The beam runs full diameter end to end. A full-diameter beam flexes less and puts more of your torque into holding the head down instead of into stretching the stud, which also makes your torque readings more honest when you tighten the nuts.\u003c\/p\u003e\n\n\u003ch4\u003eWhat's in the Kit\u003c\/h4\u003e\n\n\u003cp\u003eStuds, nuts, washers, assembly lube, and instructions. Everything the job takes, in the box.\u003c\/p\u003e\n\n\u003ch4\u003eFitment\u003c\/h4\u003e\n\n\u003cp\u003eFits the H22 VTEC engine in the 1993-2001 Honda Prelude.\u003c\/p\u003e\n\n\u003ch4\u003eInstallation Notes\u003c\/h4\u003e\n\n\u003cp\u003eThis is a job for when the head is off, during a gasket or head service. Spin each stud into the block by hand only, never torqued into the block itself, and let the nuts up top do the work. Lube the threads and the underside of the nuts with what's in the kit, because dry threads lie to your torque wrench and leave the head under-clamped. Then work up to spec in stages, in the sequence the instructions give, and the head is locked down for whatever the H22 throws at it.\u003c\/p\u003e\n\u003c\/li\u003e\n\n \n\u003cli id=\"VehicleFitment\"\u003e\n \u003cp\u003e1992-1996 Honda Prelude\u003cbr\u003e1997-2001 Honda Prelude\u003c\/p\u003e \n\u003c\/li\u003e\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\u003c\/ul\u003e\n","brand":"InlinePro","offers":[{"title":"Alloy - Extreme Duty","offer_id":69878723182626,"sku":"ILP-HS-H22","price":349.95,"currency_code":"USD","in_stock":false},{"title":"Super Alloy - Xtreme Power","offer_id":69878723215394,"sku":"ILP-HS-H22SA","price":499.95,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/2218\/5701\/files\/inlinepro-h22-head-studs-for-9_mfaj.jpg?v=1794793712","url":"https:\/\/www.hybrid-racing.com\/products\/inline-pro-h22-head-studs-honda-prelude","provider":"Hybrid Racing","version":"1.0","type":"link"}