{"product_id":"golden-era-parts-rear-hatch-upper-trim-clips-88-91-crx","title":"Golden Era Parts Rear Hatch Upper Trim Clips for 88-91 CRX","description":"\u003cul\u003e\n\u003cli\u003eDirect Aftermarket Replacement for Factory Parts \u003c\/li\u003e\n\u003cli\u003eClip Includes Foam Washer \u003c\/li\u003e\n\u003cli\u003eSold as Pack of 5 Clips \u003c\/li\u003e\n\u003cli\u003eCompatible with 88-91 CRX \u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003c!-- split --\u003e\n\u003cul class=\"tabs\"\u003e\n\u003cli\u003e\u003ca class=\"active\" href=\"#Description\"\u003eDescription\u003c\/a\u003e\u003c\/li\u003e\n \u003cli\u003e\u003ca href=\"#VehicleFitment\"\u003eVehicle Fitment\u003c\/a\u003e\u003c\/li\u003e \u003c\/ul\u003e\n\u003cul class=\"tabs-content\"\u003e\n\n\n\u003cli class=\"active\" id=\"Description\"\u003e\n\u003ch3\u003eGolden Era Parts Rear Hatch Upper Trim Clips - 1988-1991 Honda CRX (Set of 5)\u003c\/h3\u003e\n\n\u003cp\u003e\n  Restoring your CRX and finding the rear hatch upper trim clips cracked, crumbled, or just plain missing?\n  You're not alone, these little clips are 30-plus years old, and once they go brittle they snap and let your\n  upper molding rattle, lift, and eventually walk right off the car. Good luck finding fresh ones from Honda.\n  That's exactly what Golden Era Parts made these for. It's a complete set of 5 clips with the EPDM rubber\n  seal, built to put your rear hatch trim back on tight and correct.\n\u003c\/p\u003e\n\n\u003ch4\u003eThe Part That Actually Matters: These Aren't 3D Printed\u003c\/h4\u003e\n\u003cp\u003e\n  Here's the thing that sets these apart, and if you've shopped for CRX repro clips you already know the\n  problem. A lot of the reproduction clips out there are 3D printed, which means they're often brittle,\n  dimensionally off, and they break or don't quite fit right. Golden Era didn't go that route. These are\n  properly injection molded from nylon, built exactly to the original Honda specification in every detail. So\n  they snap in and hold like the factory clips did, not like a printed part you're crossing your fingers on.\n  For a proper restoration, that difference is the whole point.\n\u003c\/p\u003e\n\n\u003ch4\u003eA Smart Two-Part Design\u003c\/h4\u003e\n\u003cp\u003e\n  Here's a detail you'll appreciate: these clips are two-part, and that gives you options depending on how\n  deep your restoration goes. If you're pulling the rear glass, you replace the whole clip. But if you're not\n  taking the glass out, you can just remove the upper section and attach it to your original lower sections,\n  no need to disturb the glass at all. That flexibility makes them a lot easier to work with, whether you're\n  doing a full teardown or just freshening up the trim.\n\u003c\/p\u003e\n\n\u003ch4\u003eSold As A Complete Set\u003c\/h4\u003e\n\u003cp\u003e\n  This comes as a full set of 5 clips, which is exactly what your rear hatch upper molding uses, so you're\n  replacing all of them in one shot instead of chasing down singles. They're only available as a set of 5,\n  and they replace factory part number 91508-SH2-003 (the rear windshield upper molding clip), five of them.\n\u003c\/p\u003e\n\n\u003ch4\u003eWhat You Get\u003c\/h4\u003e\n\u003cul\u003e\n  \u003cli\u003eGolden Era Parts rear hatch upper trim clips, complete set of 5\u003c\/li\u003e\n  \u003cli\u003eEPDM rubber seal included\u003c\/li\u003e\n  \u003cli\u003eInjection molded nylon, built to OE specification (not 3D printed)\u003c\/li\u003e\n  \u003cli\u003eTwo-part design, upper section can attach to your original lower sections\u003c\/li\u003e\n  \u003cli\u003eReplaces factory part number 91508-SH2-003 (5x)\u003c\/li\u003e\n  \u003cli\u003eOnly sold as a set of 5\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch4\u003eFits These Cars\u003c\/h4\u003e\n\u003cul\u003e\n  \u003cli\u003e1988-1991 Honda CRX (US, 2nd generation)\u003c\/li\u003e\n  \u003cli\u003e1987-1992 Honda CRX (worldwide, 2nd generation)\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003e\n  Note: Golden Era Parts rear hatch upper trim clips for the second-generation Honda CRX, 1988-1991 US and\n  1987-1992 worldwide. Sold as a complete set of 5 clips with an EPDM rubber seal. These are properly\n  injection molded nylon components built exactly to the original Honda specification, not 3D printed. The\n  clips are two-part, so if you are not removing the rear glass during your restoration, the upper section can\n  be removed and attached to your original lower sections. Replaces factory part number 91508-SH2-003 (CLIP,\n  RR. WINDSHIELD UPPER MOLDING), five per set. Only available as a set of 5. One set per order.\n\u003c\/p\u003e\n\u003c\/li\u003e\n\n \n\u003cli id=\"VehicleFitment\"\u003e\n 1988-1991 Honda CRX \n\u003c\/li\u003e\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\u003c\/ul\u003e\n","brand":"Golden Era Parts","offers":[{"title":"Default Title","offer_id":45877342797858,"sku":"GEP-CRX-RGC","price":36.95,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/2218\/5701\/files\/OwTv57EntA-58eAKPPS_007_Product_processed.png?v=1783011541","url":"https:\/\/www.hybrid-racing.com\/products\/golden-era-parts-rear-hatch-upper-trim-clips-88-91-crx","provider":"Hybrid Racing","version":"1.0","type":"link"}