Hybrid Racing Competition Shifter Cable Bushings Install Guide

Remove OEM shifter cable bushings from the transmission bracket without bending cables, separate and install Hybrid Racing Delrin bushings into the cable ends until they snap, lube the center bushing with Super Lube, reinsert and lock it, then reinstall cables with grease and clips and verify smooth shifting.

Black Hybrid Racing shifter cable bushing with logo facing up beside its separated center insert.
New Hybrid Racing bushing pre-assembled; hold logo up and separate the center insert before install.
Difficulty
Easy
Steps
8
Time required
15 min – 30 min
Category
Drivetrain

This guide explains how to install Hybrid Racing Competition Shifter Cable Bushings. Remove the OEM bushings from the transmission bracket without bending the cables, separate and fit the Delrin bushings until they snap in place, lube and lock the center bushing, then reinstall the cables.

Tools

  • Flathead Screwdriver / Pry Tool
    Quantity: —

01 OEM bushing removal

Two shifter cable ends with OEM rubber bushings after removal from the transmission bracket.
OEM rubber bushings still seated on the shifter cable ends, ready to be pried out with a flat tool.
Hand holds shifter cable end while flat screwdriver pries out the OEM rubber bushing.
Use a flat-tipped screwdriver to pry the OEM rubber bushing out of the shifter cable end.
Flat screwdriver prying OEM rubber bushing from shifter cable end beside a cable with bushing removed.
Pry the OEM rubber bushing out of the shifter cable end with a flat-tipped screwdriver; the lower cable shows it removed.
  1. noteSince the process to remove the shifter cable bushings will be the same for all cars we will depict that. The method or process to remove the shifter cables from the car will depend on the specific model and application.
  2. noteYou do not need to remove the shifter cables to install the new bushings. However to MUST remove them from the transmission cable bracket. Most applications will have spring C clips that hold them in place. Or they will be bolted to the bracket. You must remove them from the bracket so they can be moved freely.
  3. cautionIf you do not remove them from the OEM brackets, you risk bending and ruining the shifter cable. BE VERY CAREFUL NOT TO BEND THEM.
  4. Begin this process by removing the shifter cables from the transmission bracket. (not shown)
  5. Use a flat-tipped screwdriver or similar pry tool and pry the OEM rubber bushing out. You can spray lube on the ends to help.

02 OEM bushing removal

Hand holds black OEM bushing with metal tool through its center beside the shifter cable end.
Larger OEM bushing held after removal from the shifter cable end, with tool through its center.
Hand removes larger black OEM bushing from shifter cable end with a metal tool.
Follow the same process to remove the larger bushing from the shifter cable end.
Hand holds metal shifter cable end while flat screwdriver pries black OEM bushing free of the eyelet.
Pry the larger black OEM bushing out of the metal eyelet on the shifter cable end.
  1. Follow the same process and remove the larger bushing.

03 Seperate the HR bushing

Hands hold the black Hybrid Racing bushing with logo facing upward on a wooden surface.
Hold the bushing with the Hybrid Racing logo facing upwards before separating the center.
Hands hold Hybrid Racing bushing with center aligned to large openings in the Delrin ring
Rotate the center bushing so it aligns with the large portions of the Delrin ring as marked.
Hands hold the separated Hybrid Racing Delrin outer case and aluminum center bushing after removal.
After rotating to align, the aluminum center bushing is pushed outward and fully separated from the Delrin case.
  1. The new Hybrid Racing bushing comes pre-assembled in the package. You must remove the center bushing before installing it in the shifter cable end ring.
  2. This process is very easy. Hold the bushing with the Hybrid Racing logo facing upwards.
  3. Use your fingers and rotate the center bushing so that it aligns with the large portions of the delrin ring.
  4. Push the aluminum bushing outward, separating it from the Delrin case.

04 Install small bushing

Hands hold small Delrin bushing with arrows marking tabs to compress for shifter cable end.
Compress the tabs on the small Delrin bushing (arrows) so it can clip into the cable end.
Hands compress Delrin bushing tabs to slide it into the shifter cable end.
Squeeze the bushing tabs and align it to slide into the cable end until it snaps in place.
Hand holds shifter cable end with small Delrin bushing snapped into place on wooden surface.
After compressing the tabs, the small bushing snaps fully into the cable end to complete installation.
  1. The tabs of the Delrin bushing must be compressed so it can clip into the cable end.
  2. Be sure to align it correctly, squeez the tabs and slide the bushing into the cable end.
  3. You will hear the bushing "snap" into place. Once that happens, the installation is complete.

05 Install main bushing

Hands hold the main bushing, four tabs arrowed, above the shifter cable end.
Depress the four tabs on the main bushing before sliding it into the cable end.
Hand holds outer ring on shifter cable end beside Hybrid Racing main bushing on wood surface.
See the outer ring held on the cable end with tabs ready to face down, main bushing nearby before sliding it on.
Hands sliding the silver outer ring onto the shifter cable end while installing the main bushing
Slide the outer ring through the top of the cable end until the main bushing snaps into place.
  1. Similar to the previous step, the main bushing has four tabs that must be depressed before sliding it into the cable end.
  2. Make sure you have the shifter cable facing the correct way. The tabs that get depressed will face down on the shifter cable. So be sure you slide the outer ring through the top section of the cable.
  3. Slide the ring into place and make sure you hear it snap.

06 Add Super Lube

Hands apply Super Lube grease with PTFE from a packet onto the black center bushing above the shifter cable end.
Apply a bit of Super Lube grease with PTFE to the center bushing, then spread it evenly so the bushing moves smoother.
Hands hold Hybrid Racing center bushing with Super Lube grease applied around it above the Delrin ring.
Super Lube grease is applied around the Hybrid Racing center bushing and ready to be spread evenly.
Hands hold the black center bushing above the open shifter cable end with Delrin ring on the work surface.
Apply Super Lube grease with PTFE to the center bushing, then spread it evenly before reassembly.
  1. Even though the bushing and Delrin ring are very smooth, we recommend adding a bit of Super Lube grease with PTFE to the center bushing.
  2. This allows the bushing to move even smoother. Once applied to the bushing, spread it out evenly.

07 Insert the center bushing

Hands hold the black Hybrid Racing center bushing above the shifter cable end ring on a wooden surface.
Hold the lubed center bushing ready to align and insert into the ring on the shifter cable end.
Hands insert the greased center bushing into the shifter cable end ring.
Align the ring sides with the lubed center bushing and slide it in before rotating 90° to lock.
Hybrid Racing center bushing locked onto the end of the shifter cable
Center bushing inserted and rotated 90 degrees to lock it in place on the cable.
  1. Now that the bushing is lubed, you can insert it back into the bushing the same way it was removed.
  2. Aling the sides of the ring with the bushing and slide it in. Once inserted, rotate it 90* to lock it in place.
  3. The bushing should move freely and will not come out.

08 Grease and install

Hybrid Racing shifter cable bushings on cable ends, arrows marking the center openings
Arrows point to the bushing centers on the cable ends before greasing the gear selector pin and clipping them on.
Hybrid Racing shifter cable bushings with metal clips on both transmission gear selector pins.
Supplied clips hold the greased bushings onto the gear selector pins with cables reinstalled.
  1. You can now install the shifter cables back on the transmission. Use the supplied great and apply it on the gear selector pin.
  2. Use the supplied clips to hold the bushings onto the gear selector.
  3. Shift through all gears and make sure everything feels smooth.
  4. The installation is complete, now go rip!

Finishing up

Reinstall the shifter cables with the supplied grease on the gear selector pin and the supplied clips. Shift through all gears and confirm everything feels smooth. Installation is complete.