Hybrid Racing CMC Upgrade 17-21 Civic Type-R Install Guide

Use this guide as a reference to install the Hybrid Racing CMC kit on the 17-21 Civic Type R.

Hybrid Racing CMC upgrade kit parts including master cylinder, clutch line, and hardware for Civic Type R.
Cover photo showing the full Hybrid Racing CMC upgrade kit contents before installation on the 17-21 Civic Type-R.
Difficulty
Moderate
Steps
27
Time required
2 hr
Category
Drivetrain

This guide covers installation of the Hybrid Racing CMC upgrade on the 17-21 Civic Type R.

Tools

  • hardline wrench

    Used to unbolt the clutch line from the CMC

    Quantity: —
  • vacuum bleeder

    Suggested for bleeding the clutch release system; a hand vacuum pump may be used instead

    Quantity: —

01 Remove Battery

Honda battery in Civic Type R engine bay; yellow arrows mark tie-down stud and nearby cable.
Yellow arrows show the battery tie-down bracket stud and cable to disconnect before removing the battery.
Green arrows mark battery tie-down points beside the Honda battery in the engine bay.
Green arrows show the battery tie-down bracket locations to remove after disconnecting the battery.
Black battery with red positive cover in Civic engine bay beside ratchet tools on blue cloth.
View the battery in the engine bay with tools laid out on the cloth for disconnecting and removing the tie-down.
  1. Begin by disconnecting the battery and removing the battery tie-down bracket.

02 Remove Intake

Gloved hands use a tool on the silver inlet pipe while removing the airbox in the engine bay.
Unbolt and remove the airbox up to the inlet pipe to reach the lower slave cylinder area.
Ratchet set on blue towel beside open airbox with red filter and long extension tool in Civic Type R engine bay.
Tools rest on a towel next to the airbox housing as it is unbolted and removed up to the inlet pipe for slave cylinder access.
Gloved hand lifts black airbox clear of the inlet pipe in the Civic Type R engine bay.
Remove the airbox up to the inlet pipe so you can reach the lower slave cylinder section.
  1. Unbolt and remove the airbox up to the inlet pipe. This will help you access the lower section of the slave cylinder.

03 Remove Battery Tray

Gloved hand grasping the black plastic battery tray with red terminal cover in the Civic Type R engine bay.
View the plastic battery tray still installed; remove it and unbolt the battery bracket from the tray and frame.
Gloved hand reaches beside the red battery terminal cover in the Civic Type R engine bay.
Note the battery tray and bracket area by the red terminal cover while unbolting the tray and frame.
Gloved hands use a ratchet on a bolt at the battery tray and bracket in the Civic Type R engine bay.
Unbolt the remaining fasteners on the plastic battery tray and frame before lifting the battery bracket out.
  1. Remove the plastic battery tray and unbolt the battery bracket. Be sure to remove the bolts on the tray and frame.
  2. Remove the battery bracket from the car.

04 Remove Pin & Clip

Hands hold the brake pedal while pliers grip the retaining clip on the clevis pin.
Use pliers to remove the retaining clip at the pedal so the pin can free the clevis.
Hand holds the removed clevis pin with a yellow arrow pointing to its worn tip near the brake pedal.
Look at the removed pin tip after freeing the clevis from the pedal; the arrow highlights wear on the pin end.
12mm nut on the CMC bracket beside the clutch pedal inside the Civic Type R cabin
Arrow points to one of the two 12mm nuts on the CMC bracket to remove so it can slide outward.
  1. Inside of the car, remove the retaining clip at the pedal.
  2. Remove the pin to free the clevis from the pedal.
  3. Remove the two 12mm nuts so the CMC can slide outward.

05 Remove Access Panel

Gloved hand grasps the rubber cowl seal along the base of the windshield below the wiper arms.
Remove the rubber cowl seal from the base of the windshield as the first part of clearing the access panel.
Gloved hand lifts the rubber cowl seal from the plastic panel below the windshield wipers.
Lift and remove the rubber cowl seal from along the base of the windshield cowl panel.
Rubber cowl seal and plastic reservoir access cap below the windshield cowl grille near the washer reservoir.
View the rubber cowl seal and plastic reservoir access cap in place along the cowl for removal.
  1. Remove the rubber cowl seal.
  2. Remove the plastic reservoir access cap.

06 Unbolt Clutch Line

Clutch line bolted to the CMC mounted on the firewall in the engine bay.
Locate the clutch line connection on the CMC to unbolt it with a hardline wrench.
Gloved hand holds the unbolted clutch line fitting near a green O-ring and blue cloth by the CMC.
See the clutch line fitting freed from the CMC, with the green O-ring and blue cloth visible in the engine bay.
  1. Use a hardline wrench and unbolt the clutch line from the CMC.

07 Remove CMC & Seal

CMC and firewall seal in the Civic Type R engine bay, red arrows marking both for removal.
Red arrows show the CMC and firewall seal to remove from the vehicle in this step.
Gloved hand holds the removed silver CMC with attached hose above the Civic Type R engine bay.
CMC removed from the vehicle; also pull off the firewall seal for the included replacement.
  1. Remove the CMC from the vehicle.
  2. Be sure to remove the firewall seal as well. We include a replacement.

08 Secure Reservoir Hose

Gloved hands secure the reservoir line hose with a zip tie near clutch components in the engine bay.
Secure the removed reservoir hose to the crown with the supplied zip tie.
Black reservoir hose with clamp and zip tie secured upright near the engine bay crown above the coolant cap.
Reservoir line hose removed and zip-tied to the crown to keep it upright and prevent fluid loss.
  1. Remove the reservoir line hose and secure to the crown with the supplied zip tie.
  2. This is done to prevent the lose of fluid.

09 Remove Clutch Line Brackets

Clutch line bracket bolt circled near the metal support arm in the Civic Type R engine bay.
Unbolt the clutch line bracket at the circled fastener shown in this step.
Clutch line secured in a metal bracket with a bolt on the engine bay of the Civic Type R.
Locate the clutch line bracket and unbolt it to free the clutch line for the CMC upgrade.
  1. Unbolt the clutch line brackets.

10 Remove Under Tray

Under tray on the Civic Type R underside with mounting bolts detached and unlock/lock fastener detail.
Remove the under tray by taking out its bolts and turning the fasteners to the unlock position as shown.
Civic Type R underside with blue oil filter, engine, and exhaust flex pipe exposed after under tray removal.
After removing the under tray, the engine underside, oil filter, and exhaust pipe are fully visible from below.
  1. Remove the under tray.

11 Disconnect CSC

Green arrows mark the clutch line connection at the slave cylinder on the transmission.
Remove the clutch line at the slave cylinder where the green arrows indicate the connection.
  1. Remove the clutch line at the slave cylinder.

12 Remove Clutch Line

Clutch line secured in a black grommet on the engine bay bulkhead near wiring loom.
Clutch line clipped through the bulkhead grommet; unclip it here before removing the line from the car.
Olive clutch line held by a black clip on the engine bay bulkhead bracket.
Note the black clip securing the clutch line to the bracket before unclipping and removing it.
Gloved hand beside the unclipped yellow clutch line at the firewall area in the Civic Type R engine bay.
The clutch line is unclipped here and can now be pulled free from the car.
  1. Unclip the clutch line and remove it from the car.
  2. cautionBe careful not to drip brake fluid on any painted surface.

13 Remove Clutch Line

Gloved hand holds the clutch line under the Civic Type R near the transmission and chassis rails.
See the clutch line being removed from under the car, with arrows marking its path along the underside.
  1. Remove the clutch line from the car. Removing it from under the car is easier as you won't have to bend it around the engine mount.

14 Install New Line Clips

Three black clutch line mounting clips supplied with the Hybrid Racing CMC kit.
Locate the three provided black clutch line mounting clips highlighted for installation.
Clutch line mounting clip fastened to the metal bracket in the engine bay.
Note the installed clutch line mounting clip at the arrow on the bracket.
Black clutch line mounting clip installed on hose near engine bay connectors and manifold cover.
Arrow shows the installed clutch line mounting clip secured in place on the line.
  1. Install the provided clutch line mounting clips.

15 Route New Clutch Line

Gloved hand holds banjo fitting on new clutch line near engine bay hoses and frame.
Banjo fitting end of the new clutch line, routed on the CMC side under the factory brake line.
Gloved hand holds the straight fitting end of the new clutch line in the engine bay.
Straight fitting end of the routed clutch line, which goes to the CSC per the step instructions.
Green line marks the new clutch line routed low between the engine mount and frame rail area.
Follow the green line: clutch line routed between engine mount and frame rail, banjo side under the factory brake line.
  1. Route the clutch line between the engine mount and frame rail.
  2. The banjo fitting should be on the CMC side; the straight fitting goes to the CSC.
  3. noteMake sure the banjo side goes UNDER the factory brake line.

16 Secure New Clutch Line

New clutch line seated in a clip on the Civic Type R frame rail.
Install the new clutch line into the frame clips from step 14 to secure it in place.
  1. Install the line into the clips you installed on the frame in step 14.

17 Install Fitting Adapter

Black adapter fitting installed into the silver CSC housing near the clutch area.
Adapter fitting threaded into the CSC; tighten it fully for this step.
Adapter fitting installed into the CSC on the Civic Type R clutch area.
Adapter fitting tightened into the CSC after installation.
Adapter fitting installed and tightened into the CSC on the Civic Type R clutch area.
Adapter fitting fully seated and tightened into the CSC for this install step.
  1. Install the adapter fitting into the CSC, and tighten it.

18 Secure Clutch Line

Clutch line bracket bolted to the OEM mount on the front of the transmission.
Secure the clutch line bracket to the OEM mounting location on the front of the transmission.
  1. Secure the clutch line bracket to the OEM mounting location on the front of the transmission.

19 Install Line On CMC

Gloved hand holds new CMC with clutch line banjo fitting aligned to the mounting face.
Install the clutch line on the CMC so the banjo fitting is clocked in line with the mounting face.
  1. Install the clutch line on the new CMC and make sure it is clocked correctly. The fitting should be in line with the mounting face.
  2. cautionThis is done to ensure no contact between the firewall and clutchline.
  3. noteThe banjo fitting should have a washer on the top and bottom.
  4. reminderBe sure to install the new firewall seal.

20 Install CMC To Firewall

Silver CMC mounted on the Civic Type R firewall with clutch line attached.
CMC installed into the firewall; check fittings are tight and the clutch line contacts nothing.
  1. Install the CMC into the firewall.
  2. noteMake sure all fittings are tight and the clutch line doesn't contact anything. Adjust the fitting if it does.

21 Attach Reservoir Line

New silver CMC mounted on the firewall with black reservoir hose clamped to its top fitting.
Reservoir hose installed on the new CMC with the clamp reinstalled at the top fitting.
Silver Hybrid Racing CMC mounted on the firewall with the black reservoir hose attached at the top fitting.
Reservoir hose installed on the new CMC with the clamp reinstalled at the top connection.
  1. Install the reservoir hose to the new CMC and reinstall the clamp.

22 Grease Pin

Gloved hands apply grease from a tube onto the clevis pin for the CMC upgrade.
Apply the supplied grease to the clevis pin as shown.
  1. noteUse the tube of supplied grease and apply it to the clevis pin.

23 Install Pin & Clip

Gloved hand holds the OEM retaining clip near the greased clevis on the clutch master cylinder area.
Look at the OEM retaining clip indicated by the arrow, ready to reinstall after the greased clevis is in place.
Gloved hand by black CMC component with arrow pointing to OEM retaining clip on greased clevis under bracket.
Arrow shows the OEM retaining clip reinstalled on the greased clevis for this CMC upgrade step.
  1. Install the greased clevis and then reinstall the OEM retaining clip.

24 Install Spacers On CMC

Two silver metal mounting spacers for the CMC, highlighted beside black clips and Super Lube packet.
Locate the two mounting spacers shown here; install them on the CMC before securing with the factory 12mm nuts.
Factory 12mm nut secures CMC mounting spacer on the metal bracket against blue firewall insulation.
Look at the factory 12mm nut tightened on the CMC mounting spacer against the firewall.
  1. Install the mounting spacers and secure the CMC with the factory 12mm nuts.

25 Confirm Pedal Stop Location

White pedal stop contacting the black clutch pedal arm under the metal firewall bracket nut.
Confirm the clutch pedal is resting on the white pedal stop at the contact point marked by the arrow.
Hex nut and threaded pedal stop bolt on the metal bracket above the black clutch pedal.
Confirm the clutch pedal rests on the white pedal stop; loosen the nut and thread the stop down if needed.
  1. Once the CMC is tight against the firewall, pull the pedal upwards towards the pedal stop.
  2. Confirm the pedal is resting on the pedal stop.
  3. If it does not, loosen the pedal stop and thread it down until it touches the pedal.
  4. Retighten the nut and prepare to bleed the system.
  5. cautionIt is important that the pedal stop be adjusted IF NEEDED. We calibrate these parts beforehand so you shouldn't have to adjust it, however, if you do need to adjust it slightly that is fine. If you adjust the pedal stop and the pedal it still does not touch it, please stop the installation and contact us ASAP.

26 Bleed System

Gloved hand holds the yellow clutch fluid reservoir near the firewall in the open engine bay.
Keep the clutch reservoir filled while bleeding the release system with a vacuum bleeder.
Clutch fluid pouring from a bottle into the translucent clutch master cylinder reservoir in the engine bay.
Keep the clutch reservoir filled with the same fluid while bleeding the release system.
Capri Tools vacuum bleeder with white reservoir, blue knob, and clear hose for clutch bleeding.
Suggested vacuum bleeder tool for removing air from the clutch release system while keeping the reservoir filled.
  1. Bleed the clutch release system. We suggest using a vacuum bleeder or at least a hand vacuum pump to remove all of the air from the system.
  2. Be sure to keep the reservior filled during the entire sequence.
  3. Use the same fluid already installed in your car. Do not mix brake fluids.
  4. After a few minutes of bleeding, the pedal should be firm and actuate the clutch fork completely.

27 Final Checks

White 17-21 Civic Type R with Hybrid Racing livery and wing parked outdoors after CMC upgrade.
Finished Civic Type R ready for final driving checks of pedal feel and normal CMC noise after the upgrade.
Installed Hybrid Racing CMC upgrade in the driver interior of a 17-21 Civic Type R.
Finished Civic Type R interior after Hybrid Racing CMC install for final pedal engagement checks.
  1. Drive the car and take notice of the pedal engagement / disengagement.
  2. You may notice more vibrations and noice with this master cylinder. That is normal. The pedal does not have a damper so all of the NVH will be trasnmissited through the line to the pedal.
  3. It will feel more consistent, but the system can be noisier than the OEM parts.
  4. Enjoy rippin!

Finishing up

Drive the car and note pedal engagement and disengagement. More vibration and noise are normal without a damper, as NVH transmits to the pedal. The feel should be more consistent, though noisier than OEM. Enjoy rippin!