Hybrid Racing Clutch Master Cylinder Upgrade for 06-11 Civic Si Install Guide

This guide will show you how to install the EM1 CMC upgrade kit in a 2006-2011 Honda Civic Si. ONLY PART NUMBER HYB-CMC-01-02

Hybrid Racing clutch master cylinder with braided hose and pushrod clevis
Cover photo of the Hybrid Racing EM1 CMC upgrade kit (HYB-CMC-01-02).
Difficulty
Moderate
Steps
16
Time required
1 hr
Category
Drivetrain

This guide shows how to install the EM1 CMC upgrade kit (part number HYB-CMC-01-02) in a 2006-2011 Honda Civic Si.

Tools

Parts

01 Begin by disconnecting the negative terminal of the battery.

Hands use a wrench on the negative battery terminal in the engine bay.
Loosen and disconnect the negative battery terminal first as shown.
Hand uses a ratchet wrench on the positive battery terminal clamp in the engine bay.
After the negative, remove the positive terminal clamp from the battery.
Socket wrench on the battery hold-down bracket bolt atop the car battery in the engine bay.
Loosen the battery bracket after the terminals are disconnected.
  1. Begin by disconnecting the negative terminal of the battery.
  2. Next remove the positive terminal, then loosen the battery bracket.

02 Once the battery bracket is loose, rotate the studs and pull the assembly out.

Hand lifts the loose battery hold-down bracket off its stud atop the battery in the engine bay.
Once loose, rotate the studs and pull the battery bracket assembly up and out of the engine bay.
Hands lift the black plastic battery cover off the battery in the Civic engine bay.
Lift up on the battery cover and remove it from the battery assembly.
Hands lift the black battery out of the engine bay.
Lift the battery up and remove it from the car.
  1. Once the battery bracket is loose, rotate the studs and pull the assembly out.
  2. Lift up on the battery cover and remove it.
  3. Remove the battery from the car.

03 Remove the battery tray cover to expose the battery tray.

Hands lift the black battery tray cover off the engine bay tray on a Honda Civic Si.
Remove the battery tray cover to expose the battery tray underneath.
Battery tray exposed in the engine bay after the battery tray cover has been removed.
With the cover off, the bare battery tray is visible in the engine bay for this step.
  1. Remove the battery tray cover to expose the battery tray.

04 Use a pair of clamping pliers to pinch the reservoir fluid line that runs to the clutch master cylinder.

Clamping pliers pinch the reservoir fluid line at the clutch master cylinder.
Pinch the reservoir fluid line to the clutch master cylinder with clamping pliers to prevent leaks.
  1. Use a pair of clamping pliers to pinch the reservoir fluid line that runs to the clutch master cylinder.
  2. Doing this will prevent an unwanted leak of the fluid. You can drain the used fluid into a brake fluid safe container for disposal.

05 Using a metric line wrench, remove the factory clutch line from the clutch slave cylinder.

Factory clutch line fitting connected to the clutch slave cylinder, circled in the engine bay.
Locate the factory clutch line at the clutch slave cylinder fitting before removing it with a metric line wrench.
Factory clutch line still threaded into the fitting on the clutch slave cylinder in the engine bay.
Factory clutch line connected at the clutch slave cylinder fitting before removal with a line wrench.
  1. Using a metric line wrench, remove the factory clutch line from the clutch slave cylinder.
  2. You may need to hold the CSC fitting with another wrench.

06 Remove the lower dash panel to allow for easier access to the pedal assembly.

Removed lower dash panel with white foam padding rests on the red floor carpet in front of the exposed clutch and brake pedals.
Lower dash panel removed and set on the floor, exposing the pedal assembly for easier clutch master cylinder access.
Clutch master cylinder pin with metal retaining clip on the pedal assembly.
Locate the clutch master cylinder pin held by the metal clip on the pedal assembly for removal.
Wrench loosening the clutch interlock switch sensor on the pedal assembly under the dash
Loosen the clutch interlock switch sensor with the wrench; keep it loose for final clutch adjustment.
  1. Remove the lower dash panel to allow for easier access to the pedal assembly.
  2. Locate and remove the clutch master cylinder pin.
  3. Loosen the clutch interlock switch sensor. You will need this loose for clutch adjustment at the end of the install.

07 Using a 12mm socket, remove the two mounting nuts that hold the clutch master cylinder in place.

Two mounting nuts securing the clutch master cylinder to the firewall.
Orange circles mark the two mounting nuts holding the clutch master cylinder in place for removal.
Clutch master cylinder on the firewall with a lower mounting stud exposed after nut removal.
Look at the exposed lower mounting stud on the clutch master cylinder after its nut is removed.
  1. Using a 12mm socket, remove the two mounting nuts that hold the clutch master cylinder in place.

08 Locate the three mounting locations for the factory clutch line. Un-clip them all now.

Gray factory clutch line secured in a black plastic clip on the underside of a black panel.
Locate this factory clutch line mounting clip and unclip the line from it.
Green plastic clip securing the black factory clutch line near corrugated hoses in the engine bay.
Locate this green clip among the three factory clutch line mounts and un-clip it.
White plastic clip holding the factory clutch line at a mounting point on the engine bay firewall area.
Third factory clutch line mounting clip circled; unclip this remaining retainer from its bracket.
  1. Locate the three mounting locations for the factory clutch line. Un-clip them all now.

09 Un-clip the factory wiring harness from its mounting bracket.

Hand presses the blue clip to free the factory wiring harness from its mounting bracket.
Un-clip the factory wiring harness from the mounting bracket as shown.
Hand unclipping the blue connector on the factory wiring harness near the clutch master cylinder.
Un-clip the factory wiring harness from its mounting bracket in the engine bay.
Hand supports clutch master cylinder assembly in Civic Si engine bay, red circle on top connection.
Support the clutch master cylinder while removing the reservoir fluid line from its top fitting, then lift the assembly free.
  1. Un-clip the factory wiring harness from its mounting bracket.
  2. Remove the reservoir fluid line from the top of the clutch master cylinder, then remove the clutch master cylinder assembly & clutch line from the car.

10 Remove the factory CMC gasket.

Gloved hands hold the clutch master cylinder and pull away the factory CMC gasket from its flange.
Factory CMC gasket is separated from the clutch master cylinder mounting flange during removal.
Gloved hands hold the OEM clutch master cylinder while C-clip pliers grip the rod and fork.
Use C-clip pliers to squeeze the C-clip and remove the OEM CMC rod and fork from the cylinder.
Gloved hands hold the clutch master cylinder while pliers remove the C-clip from the OEM rod and fork.
Use C-clip pliers to squeeze the C-clip and pull free the OEM CMC rod and fork.
  1. Remove the factory CMC gasket.
  2. Using a pair of C-Clip pliers, squeeze the C-clip and remove the OEM CMC rod & fork.

11 Pull the dust cover back on the EM1 CMC to expose the C-clip.

Gloved hands pull back the dust cover on the EM1 clutch master cylinder resting on a blue mat.
Pull the dust cover back on the EM1 CMC to expose the C-clip for rod removal.
Gloved hand holds EM1 clutch master cylinder with black dust cover pulled back exposing the rod end.
Dust cover pulled back on the EM1 CMC to expose the C-clip at the rod and fork.
Gloved hand holds EM1 CMC with dust cover pulled back exposing the rod and C-clip area.
Dust cover pulled back on the EM1 CMC to expose the C-clip and rod for removal.
  1. Pull the dust cover back on the EM1 CMC to expose the C-clip.
  2. Using the C-clip pliers, remove the rod and for from the EM1 CMC.
  3. noteIf you misplace or break your C-clip this one should work as a replacement: 98455A123

12 Compare the CMC's & rod/fork assemblies.

Two CMC rod and fork assemblies side by side on a blue cloth, with partial CMCs above.
Compare the CMC rod and fork assemblies; note the boot and spring on one versus the bare rod on the other.
Gloved hands hold the CMC rod and fork assembly beside the EM1 clutch master cylinder on a blue towel.
Compare the CMC rod and fork assemblies, then grease the rod before inserting it into the EM1 CMC.
Gloved hands hold the clutch rod and fork assembly beside the EM1 CMC and stock CMC on a bench.
Compare the CMC rod and fork assemblies, then grease the rod before inserting it into the EM1 CMC.
  1. Compare the CMC's & rod/fork assemblies.
  2. Be sure to grease the rod before inserting it into the EM1 CMC. You can use some of the grease that is on the CMC, or supply your own.

13 Using the C-clip pliers, insert the OEM rod & fork into the EM1 CMC. The EM1 dust boot is optional.

Gloved hands use C-clip pliers to insert the OEM rod and fork into the top of the EM1 clutch master cylinder.
Using C-clip pliers, insert the OEM rod and fork into the EM1 CMC; the dust boot is optional.
Gloved hands use C-clip pliers to seat the OEM rod and fork into the top of the EM1 clutch master cylinder.
Watch the C-clip pliers guide the OEM rod and fork into the EM1 CMC opening during installation.
Gloved hands seat the OEM rod and fork into the open top of the EM1 clutch master cylinder.
OEM rod and fork inserted into the EM1 CMC; dust boot is optional for this step.
  1. Using the C-clip pliers, insert the OEM rod & fork into the EM1 CMC. The EM1 dust boot is optional.

14 Once the EM1 CMC has the correct rod/fork, fill it with fluid. We recommend DOT 4 brake fluid.

Gloved hands hold the EM1 clutch master cylinder with a white funnel seated in its reservoir on the workbench.
White funnel sits in the EM1 CMC reservoir as the unit is held ready to be filled with fluid.
Gloved hands hold the EM1 clutch master cylinder over shop towels while pushing its rod inward.
Slowly push the rod in and watch for air bubbles at the fitting to purge air from the CMC before capping the outlet.
Black-gloved hands position a cap on the fluid outlet of the EM1 clutch master cylinder.
Cap the fluid outlet on the EM1 CMC after filling it and pushing the rod to remove air bubbles.
  1. Once the EM1 CMC has the correct rod/fork, fill it with fluid. We recommend DOT 4 brake fluid.
  2. Slowly push the rod in and watch for air bubbles to come out of the fitting. The goal of this is to remove as much air from the CMC as possible. This will aid in the bleeding process.
  3. Cap the fluid outlet on the EM1 CMC.

15 Be sure to install the copper sealing washers on both sides of the banjo fitting.

Gloved hands hold the clutch line banjo fitting with copper sealing washers on both sides.
Confirm copper sealing washers are seated on both sides of the banjo fitting before installation.
Gloved hands hold the clutch master cylinder while fitting the banjo clutch line and copper washers.
Check copper sealing washers on both sides of the banjo fitting, oriented away from the CMC mounting flange.
Gloved hands tighten the banjo fitting on the clutch line attached to the clutch master cylinder.
Tighten the banjo fitting on the clutch line, with copper sealing washers on both sides and the fitting pointed away from the CMC flange.
  1. Be sure to install the copper sealing washers on both sides of the banjo fitting.
  2. Install the clutch line with the banjo fitting pointing away from the CMC mounting flange.
  3. Tighten the banjo fitting. (8-10 ft•lbs)
  4. cautionDo not over tighten the banjo, you could strip or break the fitting.

16 Re-install the CMC into the chassis.

Gloved hand holds the clutch master cylinder assembly with braided line before chassis reinstall.
Hold the CMC with attached clutch line ready to re-install into the chassis as shown.
Gloved hands hold the NISSIN CMC near the firewall while connecting the clutch line fitting.
Reconnect the clutch line to the CMC as you re-install the master cylinder into the chassis.
Braided clutch line seated in the factory hard-line clip on the black plastic chassis bracket near the CMC.
Optional: the new clutch line mounts in the factory hard line clip on the chassis bracket beside the reinstalled CMC.
  1. Re-install the CMC into the chassis.
  2. Bleed the system and adjust the CMC rod accordingly for proper clutch engagement. Tighten the clutch interlock switch sensor once the adjustment has been made.
  3. noteOptional - The new clutch line will be able to mount in the factory hard line clips.

Finishing up

Bleed the system and adjust the CMC rod for proper clutch engagement. Tighten the clutch interlock switch sensor once the adjustment has been made.