Hybrid Racing 75MM RBC Throttle Body Install Guide

Use this guide to help understand the process of installing and maintaining the Hybrid Racing 75MM RBC throttle body part number HYB-THB-01-07.

Black Hybrid Racing 75mm RBC throttle body with silver bracket and open bore facing forward.
Cover photo of the Hybrid Racing 75mm RBC throttle body showing the housing, bore, and mounting bracket.
Difficulty
Moderate
Steps
13
Time required
1 hr
Category
Engine

This guide explains installation and setup of the Hybrid Racing 75mm RBC K Series Throttle Body (HYB-THB-01-07), including IACV options, MAP sensor mounting, throttle cable positions, idle adjustment, TPS install, and manifold mounting.

Tools

  • 8mm wrench

    loosen the lock nut on the idle set screw

    Quantity: —
  • 2.5mm Allen

    adjust the throttle stop

    Quantity: —

01 IACV System Block Off

Black IACV block-off plate, three-port gasket, and two bolts for the RBC throttle body.
IACV block-off plate kit with gasket and bolts for sealing the throttle body when removing the IACV.
Black Hybrid Racing 75mm RBC throttle body IACV port face with four red arrows marking the gasket sealing surface.
Install the supplied gasket in the correct orientation on the IACV port face before fitting the block-off plate.
Silver hex-socket NPT plug installed in the side port of the black Hybrid Racing RBC throttle body.
Note the NPT plug seated in the throttle body after fitting the IACV block-off plate and gasket.
  1. The Idle Air Control Valve system can be used in three ways with this throttle body.
  2. To completely remove the IACV, you must purchase the optional IACV block off plate. Item HYB-ICV-01-04 on the Hybrid Racing website.
  3. This block off plate is designed specifically for this throttle body however it can be used on the OEM K20A2 throttle body.
  4. Install the supplied gasket in the correct orientation. You can use a little silicone grease to condition the o-ring. Once the gasket is in place, install the block off plate and NPT plug into the body of the throttle body.
  5. This will completely remove the IACV from the engine. You MUST disable the IACV control and set your idle manually. For manual idle adjustment, view step 3.

02 IACV System With Out Coolant

Throttle body with rubber cap on lower coolant nipple and 1/8 NPT block-off plug circled on the side.
Install the supplied rubber cap on the lower coolant nipple and the 1/8 NPT block-off plug in the side port.
Black rubber cap with hose clamp fitted over the coolant nipple on the throttle body housing.
Supplied rubber cap and hose clamp installed on the coolant pass-through port for IACV use without coolant.
  1. To use this throttle body with a functional IACV but without the coolant pass through, you will need to install the supplied rubber cap and hose clamp and the 1/8th NPT block off plug.
  2. Note that the IACV and gasket are NOT included with this product and must be sourced separately.

03 IACV System With Coolant Pass Through

Throttle body side showing two circled IACV coolant fittings and barb ports.
Note the circled coolant pass-through fittings for installing the IACV, gasket, and supplied barb adapter.
Black threaded barb fitting adapter supplied for IACV coolant passthrough on the throttle body.
Supplied barb fitting adapter to install with the IACV and gasket for coolant passthrough.
  1. To have a functional IACV with coolant passthrough, you must install the IACV and gasket (sourced separately) and the supplied barb fitting adapter.

04 MAP Sensor (On Body)

Hybrid Racing 75mm RBC throttle body top with MAP sensor mounting holes circled.
Circled top holes on the throttle body show where to attach the MAP sensor with the supplied screw.
Small gold 16mm screw supplied to attach the MAP sensor on top of the throttle body.
The supplied 16mm screw for mounting the MAP sensor to the throttle body is circled in red.
MAP sensor secured with a screw on top of the Hybrid Racing 75mm RBC throttle body.
MAP sensor attached to the top of the throttle body with the supplied screw, as highlighted.
  1. Use the supplied 16mm screw to attach the MAP sensor to the top of the throttle body.
  2. This throttle body works with the OEM K-Series MAP sensor (37830-PGK-A01) or the Hondata MAP sensors.
  3. If you use the K20Z3 intake manifold and want to run the MAP sensor on the body, you must purchase the MAP sensor block off separately. (item HYB-MAP-01-08)

05 MAP Sensor Block Off

Black Hybrid Racing 75mm RBC throttle body with silver bracket and capped top port
View the Hybrid Racing 75mm throttle body top area related to the MAP sensor block off.
Gold bolt beside black MAP sensor block-off plug with mounting hole and rounded boss.
MAP sensor block-off and bolt shown for the MAP sensor delete on the Hybrid Racing 75mm RBC throttle body.
Gold screw secures black MAP sensor block-off plate atop the Hybrid Racing 75mm throttle body.
MAP sensor block-off plate is installed and held by the gold screw on the throttle body top.
  1. If you intend to use the MAP sensor somewhere else on the engine, you must purchase the MAP Sensor Block Off separately.

06 Throttle Cable Overview

Hybrid Racing 75mm RBC throttle body with colored circles marking multiple cable locations on the rotor.
Colored circles highlight the multiple throttle cable mounting locations on the rotor for correct cable positioning.
  1. This throttle body has multiple cable locations on the rotor. This allows different throttle cables to mount and control the rotation.
  2. Follow the next steps to ensure the correct throttle cable and position is used. If you do NOT use the correct cable or location the throttle may not open or close fully.

07 Throttle Cable Position 1

Hybrid Racing 75mm RBC throttle body linkage with red circle on cable position 1 bolt
Red circle marks the bolt for throttle cable position 1 on the linkage for the short cable.
Throttle cable with black boot attached to silver linkage on the Hybrid Racing 75mm RBC throttle body.
View the throttle cable seated in position 1 on the throttle body linkage for the short Hybrid Racing cable.
  1. Cable position 1 is designed for K-Swap applications using the Hybrid Racing throttle cable, item HYB-TRC-01-10. (Short Cable)
  2. This position should be used for this throttle body using cable HYB-TRC-01-10 in cars: 1994-2001 Acura Integra, 1992-1995 Honda Civic, or 1996-2000 Honda Civic

08 Throttle Cable Position 2

Throttle body with green circle on cable bracket hole for Hybrid Racing long cable position 2.
Green circle marks cable position 2 on the bracket for Hybrid Racing long cable HYB-TRC-01-05 on K-swap cars.
Throttle cable on the metal linkage of the Hybrid Racing 75mm RBC throttle body in position 2.
Throttle cable attached in position 2 on the linkage for K-swap use with the long Hybrid Racing cable.
  1. Cable position 2 is designed for K-Swap applications using the Hybrid Racing throttle cable, item HYB-TRC-01-05. (Long Cable)
  2. This position should be used for this throttle body using cable HYB-TRC-01-05 in cars: 1994-2001 Acura Integra, 1992-1995 Honda Civic, or 1996-2000 Honda Civic

09 Throttle Cable Position 3

Hybrid Racing 75mm RBC throttle body with silver linkage and yellow circle on the cable position 3 bolt
Yellow circle marks the bolt on the silver bracket for throttle cable position 3 used on RSX DC5 and Civic Si EP3.
Black throttle cable boot and silver linkage on the Hybrid Racing 75mm RBC throttle body.
Throttle cable secured in position 3 on the linkage for Acura RSX DC5 and Civic Si EP3.
  1. Cable position 3 is designed for the Acura RSX DC5 & Civic Si EP3 using the OEM Honda throttle cable and pedal.

10 Idle Set Screw

Idle set screw with lock nut and washer at the base of the Hybrid Racing throttle body housing.
Locate the idle set screw and lock nut on the throttle body for throttle plate stop adjustment.
Silver idle-stop bracket and screw on the side of the black Hybrid Racing 75mm RBC throttle body.
View the idle set screw and lock-nut area on the bracket next to the throttle stop lever for this step.
  1. Each throttle body is assembled with the throttle plate in the CLOSED position. If you are NOT using the factory IACV system, you may need to manually adjust the throttle plate stop to achieve the desired idle.
  2. DO NOT ADJUST THE IDLE UNLESS YOU NEED TO. THE FACTORY IACV SYSTEM WORKS GREAT - WE SUGGEST USING IT.
  3. To adjust the throttle stop, use an 8mm wrench and loosen the lock nut. A 2.5mm Allen is required to adjust the stop. Start the engine and monitor the idle. Slowly twist the screw to open the throttle plate. Once the desired RPM is met, torque the lock nut.

11 Throttle Position Sensor

Black Hybrid Racing 75mm RBC throttle body with TPS mounted on the housing side and metal bracket.
Throttle position sensor installed on the throttle body housing with the electrical connector visible.
Throttle position sensor mounted on the Hybrid Racing 75mm RBC throttle body with two screws.
TPS secured to the throttle body housing with the supplied screws, ready for center positioning and calibration.
Two small gold screws with washers circled among Hybrid Racing throttle body hardware.
Use the supplied 12mm screws (circled) to install the TPS on the throttle body housing.
  1. Use the supplied 12mm screws to install the TPS to the throttle body housing. This throttle body was designed to work with OEM Honda & most aftermarket sensors. Because each brand TPS has a different calibration window (hall effect vs wiper, etc) it's highly recommended to use the engine management system to display the TPS value.
  2. In most cases, setting the TPS in the center of the bolt holes will get it very close. Use the center bolts as a starting position, then verify and calibrate in the ECU software if necessary.
  3. noteIf you are NOT using an aftermarket engine management system, follow the OEM Honda TPS voltage value procedure.

12 Throttle Body Mounting

Black Hybrid Racing 75mm throttle body gasket with etching and bottom IACV cutout visible.
Install the gasket with HYBRIDRACING etching facing outward and the IACV provision at the bottom of the manifold flange.
Silver hex bolt securing the black Hybrid Racing 75mm throttle body to the intake manifold flange.
One of the four supplied bolts fastening the Hybrid Racing 75mm RBC throttle body to the intake manifold.
Black 75mm RBC throttle body bolted onto the silver intake manifold flange.
Throttle body secured to the intake manifold with the four supplied bolts after gasket alignment.
  1. Install the throttle body gasket with the etching facing OUTWARD. The IACV provision should also locate at the bottom section of the manifold flange. Failure to align these parts can result in leaks.
  2. Use the 4 supplied bolts and secure the throttle body to the intake manifold.

13 Other Notes

Hybrid Racing 75mm RBC throttle body with gold butterfly plate secured by center shaft bolts.
Note the bare butterfly plate with no sealant and the locked center shaft bolts that must not be loosened.
Hybrid Racing 75mm RBC throttle body butterfly marked 75 with HYBRIDRACING text and side linkage.
Note the bare butterfly with no graphite sealing; center shaft and mounting bolts stay locked—do not loosen them.
  1. noteNo throttle body will have graphite sealing. Our newest design incorporates proper tolerances and geometry that allows the system to seal and function without sealant. This is normal. Do NOT add any sealant or film to the butterfly.
  2. noteThe center shaft and mounting bolts are mechanically locked once they are installed. DO NOT LOOSEN THEM. If you try to remove them, you can damage the throttle body and the screws cannot be used again.
  3. noteThis product will work on the RBC and RRC intake manifolds. It does NOT fit any other manifold without modification. The Skunk2 intake manifolds do not have certain OEM sensor provisions, so be aware it may NOT work as intended.
  4. Contact Support@hybrid-racing.com if you have any issues or questions about your Hybrid Racing throttle body.

Finishing up

Confirm the gasket is oriented with the etching outward and the IACV provision at the bottom, then secure the throttle body with the supplied bolts. Do not add sealant to the butterfly. Do not loosen the center shaft or mounting bolts once installed. Contact Support@hybrid-racing.com if you have issues or questions.