Hybrid Racing 75MM PRB Throttle Body Install Guide

Use this guide to help understand the process of installing and maintaining the Hybrid Racing 75MM PRB throttle body.

Black Hybrid Racing 75MM PRB throttle body with silver bracket and open bore facing right.
Cover photo of the Hybrid Racing 75MM PRB throttle body showing the main body, bore, and mounting bracket.
Difficulty
Moderate
Steps
13
Time required
0 min
Category
Engine

This guide helps you install and maintain the Hybrid Racing 75MM PRB throttle body. It covers IACV configuration options, MAP sensor setup, throttle cable positions, idle adjustment, TPS installation, and mounting.

Tools

  • 8mm wrench

    Used to loosen the idle set screw lock nut

    Quantity: —
  • 2.5mm Allen

    Required to adjust the throttle stop

    Quantity: —

01 IACV System Block Off

Black IACV block-off plate, three-loop gasket, and two bolts for the throttle body.
IACV block-off plate kit with gasket and bolts for removing the IACV from the throttle body.
Red arrows mark gasket edges around the three IACV ports on the Hybrid Racing 75MM PRB throttle body.
Red arrows show the correct orientation for installing the supplied gasket on the IACV ports before the block-off plate.
Silver hex NPT plug installed in the side port of the black Hybrid Racing PRB throttle body.
NPT plug installed into the throttle body after the IACV block-off plate and gasket.
  1. The Idle Air Control Valve system can be used in three ways with this throttle body.
  2. To completely remove the IACV, you must purchase the optional IACV block off plate. Item HYB-ICV-01-04 on the Hybrid Racing website.
  3. This block off plate is designed specifically for this throttle body however it can be used on the OEM K20A2 throttle body.
  4. Install the supplied gasket in the correct orientation. You can use a little silicone grease to condition the o-ring. Once the gasket is in place, install the block off plate and NPT plug into the body of the throttle body.
  5. This will completely remove the IACV from the engine. You MUST disable the IACV control and set your idle manually. For manual idle adjustment, view step 3.

02 IACV System With Out Coolant

Throttle body with rubber cap on lower hose port and 1/8 NPT block-off plug installed beside IACV area.
Install the supplied rubber cap on the coolant hose port and the 1/8 NPT block-off plug as shown for IACV without coolant.
Black rubber cap and hose clamp fitted over the metal coolant port nipple on the throttle body.
Supplied rubber cap secured with hose clamp on the coolant pass-through fitting for IACV use without coolant.
  1. To use this throttle body with a functional IACV but without the coolant pass through, you will need to install the supplied rubber cap and hose clamp and the 1/8th NPT block off plug.
  2. Note that the IACV and gasket are NOT included with this product and must be sourced separately.

03 IACV System With Coolant Pass Through

PRB throttle body side view with IACV and two coolant barb fittings circled near the base.
Locate the two barb fittings on the throttle body for the IACV coolant pass-through and supplied adapter.
Black barb fitting adapter with male threads and hose barb for IACV coolant passthrough.
Supplied barb fitting adapter that installs with the IACV and gasket for coolant passthrough.
  1. To have a functional IACV with coolant passthrough, you must install the IACV and gasket (sourced separately) and the supplied barb fitting adapter.

04 MAP Sensor (On Body)

Top of Hybrid Racing 75MM PRB throttle body with MAP sensor mounting holes circled.
Note the MAP sensor mounting holes on top of the throttle body where the sensor attaches with the supplied screw.
Supplied 16mm screw among hardware for attaching the MAP sensor to the throttle body top.
The circled 16mm screw is the one used to attach the MAP sensor to the top of the throttle body.
MAP sensor fastened with a screw on top of the Hybrid Racing 75 mm throttle body.
MAP sensor attached to the top of the throttle body with the supplied screw.
  1. Use the supplied 16mm screw to attach the MAP sensor to the top of the throttle body.
  2. This throttle body works with the OEM K-Series MAP sensor (37830-PGK-A01) or the Hondata MAP sensors.
  3. If you use the K20Z3 intake manifold and want to run the MAP sensor on the body, you must purchase the MAP sensor block off separately. (item HYB-MAP-01-08)

05 MAP Sensor Block Off

Black Hybrid Racing 75mm PRB throttle body with silver bracket and capped top port
Throttle body showing the top MAP sensor port capped for the block-off or delete step.
Gold mounting bolt beside black MAP sensor block-off plug for the throttle body.
MAP sensor block-off and bolt used to seal the sensor port when deleting the MAP sensor.
Black Hybrid Racing 75mm throttle body with MAP sensor block-off plate and gold screw on top.
MAP sensor block-off plate secured by the gold screw on the top of the Hybrid Racing 75mm throttle body.
  1. If you intend to use the MAP sensor somewhere else on the engine, you must purchase the MAP Sensor Block Off separately.

06 Throttle Cable Overview

Hybrid Racing 75MM PRB throttle body rotor with multiple circled throttle cable mounting holes.
View the multiple cable locations on the rotor, marked by colored circles, for correct throttle cable mounting.
  1. This throttle body has multiple cable locations on the rotor. This allows different throttle cables to mount and control the rotation.
  2. Follow the next steps to ensure the correct throttle cable and position is used. If you do NOT use the correct cable or location the throttle may not open or close fully.

07 Throttle Cable Position 1

Red circle highlights a bolt on the throttle cable cam of the Hybrid Racing 75MM PRB throttle body.
Red circle marks the bolt for throttle cable position 1 on the throttle body cam.
Throttle cable with black boot attached to silver linkage on Hybrid Racing 75MM PRB throttle body.
View the throttle cable seated in position 1 on the throttle body linkage for the short Hybrid Racing cable.
  1. Cable position 1 is designed for K-Swap applications using the Hybrid Racing throttle cable, item HYB-TRC-01-10. (Short Cable)
  2. This position should be used for this throttle body using cable HYB-TRC-01-10 in cars: 1994-2001 Acura Integra, 1992-1995 Honda Civic, or 1996-2000 Honda Civic

08 Throttle Cable Position 2

Hybrid Racing 75MM PRB throttle body linkage with green circle on the cable attachment hole.
Green circle marks the throttle cable position 2 hole on the linkage bracket for the long Hybrid Racing cable.
Throttle cable attached to the linkage on the Hybrid Racing 75MM PRB throttle body in position 2.
View the throttle cable secured in position 2 on the throttle body linkage for the long cable K-Swap setup.
  1. Cable position 2 is designed for K-Swap applications using the Hybrid Racing throttle cable, item HYB-TRC-01-05. (Long Cable)
  2. This position should be used for this throttle body using cable HYB-TRC-01-05 in cars: 1994-2001 Acura Integra, 1992-1995 Honda Civic, or 1996-2000 Honda Civic

09 Throttle Cable Position 3

Hybrid Racing 75MM PRB throttle body showing throttle cable linkage with yellow circle on the pivot fastener.
Yellow circle marks the throttle cable attachment for position 3, used with OEM cable on RSX DC5 and Civic Si EP3.
Hybrid Racing 75MM PRB throttle body with throttle cable and black boot on the linkage arm.
Throttle cable in position 3 on the linkage, set up for Acura RSX DC5 and Civic Si EP3 with the OEM Honda cable.
  1. Cable position 3 is designed for the Acura RSX DC5 & Civic Si EP3 using the OEM Honda throttle cable and pedal.

10 Idle Set Screw

Idle set screw with lock nut and washer on the Hybrid Racing 75MM PRB throttle body.
Locate the idle set screw, lock nut, and washer on the throttle body for throttle stop adjustment.
Idle set screw and lock nut on the silver bracket of the Hybrid Racing 75MM PRB throttle body.
View the idle set screw and lock nut on the throttle body bracket for throttle stop adjustment.
  1. Each throttle body is assembled with the throttle plate in the CLOSED position. If you are NOT using the factory IACV system, you may need to manually adjust the throttle plate stop to achieve the desired idle.
  2. DO NOT ADJUST THE IDLE UNLESS YOU NEED TO. THE FACTORY IACV SYSTEM WORKS GREAT - WE SUGGEST USING IT.
  3. To adjust the throttle stop, use an 8mm wrench and loosen the lock nut. A 2.5mm Allen is required to adjust the stop. Start the engine and monitor the idle. Slowly twist the screw to open the throttle plate. Once the desired RPM is met, torque the lock nut.

11 Throttle Position Sensor

Black Hybrid Racing 75MM PRB throttle body with TPS sensor and metal bracket on the housing.
Throttle body housing with the throttle position sensor installed using the supplied screws.
Throttle position sensor mounted on the Hybrid Racing PRB throttle body housing with two screws.
TPS secured to the throttle body housing with the two mounting screws in place.
Two small gold 12mm screws for TPS mounting circled among the throttle body hardware kit.
Use these supplied 12mm screws, shown circled, to install the TPS to the throttle body housing.
  1. Use the supplied 12mm screws to install the TPS to the throttle body housing. This throttle body was designed to work with OEM Honda & most aftermarket sensors. Because each brand TPS has a different calibration window (hall effect vs wiper, etc) it's highly recommended to use the engine management system to display the TPS value.
  2. In most cases, setting the TPS in the center of the bolt holes will get it very close. Use the center bolts as a starting position, then verify and calibrate in the ECU software if necessary.
  3. noteIf you are NOT using an aftermarket engine management system, follow the OEM Honda TPS voltage value procedure.

12 Throttle Body Mounting

Black Hybrid Racing throttle body gasket with etching and bottom IACV cutout for manifold.
Orient the gasket so the Hybrid Racing etching faces outward and the IACV provision sits at the bottom of the flange.
Silver hex bolt on the black Hybrid Racing 75mm throttle body housing beside the shaft opening
Note one of the four supplied bolts securing the throttle body housing during mounting to the intake manifold.
Black Hybrid Racing 75mm PRB throttle body bolted to the silver intake manifold flange.
Throttle body secured to the intake manifold with the four supplied bolts after gasket installation.
  1. Install the throttle body gasket with the etching facing OUTWARD. The IACV provision should also locate at the bottom section of the manifold flange. Failure to align these parts can result in leaks.
  2. Use the 4 supplied bolts and secure the throttle body to the intake manifold.

13 Other Notes

Hybrid Racing 75MM PRB throttle body with bare gold butterfly plate and locked center shaft screws.
Note the bare butterfly with no graphite sealant and the mechanically locked center shaft screws that must not be loosened.
Hybrid Racing 75MM PRB throttle body with bronze butterfly marked 75 and HYBRIDRACING
Front view of the throttle body butterfly and center shaft; no sealant is present and shaft bolts stay locked.
  1. noteNo throttle body will have graphite sealing. Our newest design incorporates proper tolerances and geometry that allows the system to seal and function without sealant. This is normal. Do NOT add any sealant or film to the butterfly.
  2. noteThe center shaft and mounting bolts are mechanically locked once they are installed. DO NOT LOOSEN THEM. If you try to remove them, you can damage the throttle body and the screws cannot be used again.
  3. noteThis product will work on the RBC and RRC intake manifolds. It does NOT fit any other manifold without modification. The Skunk2 intake manifolds do not have certain OEM sensor provisions, so be aware it may NOT work as intended.
  4. Contact Support@hybrid-racing.com if you have any issues or questions about your Hybrid Racing throttle body.

Finishing up

Confirm idle adjustment only if needed (not using factory IACV), with the lock nut secured after setting. Verify TPS position and calibrate as required. Ensure the throttle body gasket is oriented correctly and the unit is secured with the supplied bolts. Do not add sealant to the butterfly, and do not loosen the mechanically locked center shaft or mounting bolts. Contact Support@hybrid-racing.com with any issues.