Hybrid Racing Performance Air Intake for 06-11 Civic Si Install Guide

This is a step by step guide on how to install the Hybrid Racing Performance Air Intake System on the 06-11 Honda Civic Si.

Hybrid Racing cold air intake kit parts with pipes, hoses, filter, bracket and clamps laid out.
Cover photo showing all components included in the Hybrid Racing Performance Air Intake kit for the 06-11 Civic Si.
Difficulty
Moderate
Steps
35
Time required
1 hr โ€“ 1 hr 30 min
Category
Engine

This is a step-by-step guide to install the Hybrid Racing Performance Air Intake System on the 06-11 Honda Civic Si.

Tools

  • Metric Socket Set
    Quantity: 1
  • Socket Extensions
    Quantity: 1
  • Large Flat Head Screwdriver
    Quantity: 1
  • #2 Phillips Head Screwdriver
    Quantity: 1
  • Plier Set
    Quantity: 1
  • Drain Pan
    Quantity: 1
  • 5mm Allen Wrench
    Quantity: 1

01 Disconnect Battery

Hands use a wrench on the negative terminal of the yellow battery in the Civic Si engine bay.
Remove the negative battery terminal first with a wrench, then the positive, before taking off the battery tie down.
Hands lift the red cover and loosen the positive terminal on the yellow battery in the Civic engine bay.
After the negative, lift the red cover and remove the positive battery terminal clamp.
Impact driver loosens the bolt on the black battery tie-down bracket atop the yellow battery.
Hold the battery tie-down steady while removing its securing bolt after the terminals are disconnected.
  1. Remove the negative terminal of the battery first then remove the positive.
  2. Once the battery has been disconnected, remove the battery tie down.

02 Drain Coolant

Hand gripping the red radiator cap on the engine bay near the black Hybrid Racing cover.
Remove the radiator cap once the engine is cool so you can drain coolant at the petcock.
White plastic petcock valve seated in the lower radiator housing on the Civic Si.
Locate the petcock on the lower radiator; twist it open just enough for coolant to begin draining.
Green drain pan under the Civic Si front bumper collecting coolant from the lower radiator.
Coolant flows into the clean green drain pan placed beneath the lower radiator petcock.
  1. Remove the radiator cap then open the petcock on the lower radiator. You shouldn't need to remove it completely, just twist it until coolant starts to flow.
  2. cautionNever remove the radiator cap when the car is hot. Wait until the radiator and engine is cool to the touch.
  3. reminder

    If you plan on re-using the engine coolant, be sure to use a clean drain pan. You should never re-use dirty or discolored fluids.

  4. noteYou do not need to drain the system completely of coolant. You will be replacing the upper radiator hose only so as long as the fluid level is below that it is ok.

03 Remove underpanel

Hand holding a long ratchet on a screw fastening the bumper to the fender bracket by the front tire.
Remove the screw that fastens the bumper to the fender bracket on each side, pulling back the fender lining for access.
Metal pry tool lifting a plastic clip from the black underpanel on the Civic Si.
Use the pry tool to remove the plastic clip holding the lower bumper to the underpanel.
Drill with hex bit removing screw at bumper-to-fender bracket behind pulled-back fender lining.
Remove the screw fastening the bumper to the fender bracket; pull back the fender lining for access.
  1. Remove all of the clips that hold the lower portion of the bumper to the lower plastic cover.
  2. Remove the screws that fasten the bumper to the fender bracket. There is one on each side. You may have to pull back the fender lining to gain access.

04 Remove bumper cowl

Hand uses a wrench on a plastic clip securing the upper grill cover near the headlight.
Remove the clips that attach the upper grill cover near the headlight and bumper edge.
Hand removing a retaining clip from the black upper grill cover in the Civic Si engine bay.
Remove the clips attaching the upper grill cover before sliding the cover backwards to take it off.
Hands slide the black upper grill cover backward off the front of a Honda Civic Si.
Slide the upper grill cover backward and lift it completely off the bumper cowl area.
  1. Remove the clips that attach the upper grill cover.
  2. Slide the cover backwards and remove it completely.

05 Remove Bumper

Honda Civic Si front bumper and grille still installed with hood open and engine bay exposed.
Front bumper and grille after the upper cover is out of the way, ready to unbolt the grill brackets.
Hand uses a long screwdriver on a fastener at the front bumper bracket near the headlight.
With the upper cover clear, remove the bolts holding the grill brackets so the bumper sides can unsnap.
Hand grips the lower right corner of the front bumper on a gray Honda Civic Si with the hood open.
With the bumper snaps released, pull the front bumper free from the passenger-side brackets and remove it carefully.
  1. Once the upper cover is out of the way, remove the bolts that hold the grill brackets in place.

  2. The sides of the bumper snap in place. Once both screws are removed, you'll need to pop the bumper out of the brackets.

  3. Remove the bumper.

  4. cautionDo not yank on the bumper as it could over stress the paint which can result in cracks or chips.

06 Remover Overflow bottle

Hands lifting the radiator overflow reservoir from its mount beside the battery in the engine bay.
Lift the radiator overflow reservoir straight up to remove it from the engine bay.
  1. Remove the radiator overflow reservoir.

07 Remove battery bracket

Two bolts hold the battery tray to the wire harness bracket in the Civic Si engine bay.
Remove the two bolts securing the battery tray to the wire harness bracket, shown circled.
Hand holding unclipped wiring harness connector beside battery tray bracket clips in Civic Si engine bay.
Unclip the wiring harness from the battery tray bracket at the two circled connectors and move it aside.
Wire harness bracket and battery tray bolt in the Civic Si engine bay near intake tubing
View the battery tray bolts on the wire harness bracket after the harness is unclipped and moved aside.
  1. Remove the bolts that hold the battery tray to the wire harness bracket.
  2. Unclip the wiring harness and move it out of the way.

08 Remove Battery Tray

Long chrome socket extension engaged on a battery tray bolt in the engine bay.
Socket extension on a lower battery tray bolt being removed.
Hand with screwdriver removing a bolt on the battery tray in the Civic Si engine bay.
Remove the remaining upper and lower battery tray bolts; there are four total before lifting the tray out.
Gray battery tray still mounted in the engine bay under the intake tube and Skunk2 cover.
Battery tray in place after the four upper and lower bolts have been removed, ready to lift out.
  1. Remove the upper and lower battery tray bolts. There are 4 total.
  2. Remove the battery tray.

09 Remove Upper Intake Tube

Hands grasp and lift the upper air intake tube from the engine bay on a 06-11 Civic Si.
Lift and remove the upper portion of the stock air intake tube from the engine bay.
Engine bay of 06-11 Civic Si with upper air intake tube removed, exposing hoses and wiring.
Engine bay after the upper portion of the air intake tube has been removed for this step.
  1. Remove the upper portion of the air intake tube.

10 Remove Lower Air Tube

Craftsman impact driver on a fastener securing the lower air intake tube beside the front wheel well.
Use the power tool on the fastener while preparing to twist and pull the lower air tube free.
Hands twist and pull the lower air intake tube from the front engine bay area.
Twist and turn while pulling the lower section of the air intake tube free from the vehicle.
Lower air intake tube mounting area with metal brackets and wiring in the front chassis of the Civic Si.
Empty space in the chassis after the lower air intake tube has been twisted free and removed.
  1. With the bumper off, remove the lower section of the air intake tube.
  2. It's doesn't come out easily so you will have to twist and turn while pulling. Make sure everything has been disconnected before you start to yank on it.

11 Disconnect MAF wiring

Hands unplug the MAF sensor connector on the intake in the Civic Si engine bay.
Unplug the MAF sensor wiring connector from the top section of the intake.
Black MAF sensor seated on the polished intake tube in the Civic Si engine bay.
Locate the MAF sensor on top of the intake tube to unplug its wiring connector.
Chrome socket on a bolt securing the top of the Takeda intake tube in the engine bay.
Socket on the bolt holding the top section of the intake in place, ready to be removed.
  1. Unplug the MAF sensor and remove any bolts holding the top section of the intake in place.

12 Unbolt Intake

Screwdriver loosening the hose clamp on the black intake tube at the throttle body.
Loosen the clamp closest to the throttle body on the intake tube.
Pliers gripping an accessory tube on the Takeda intake pipe near the throttle body.
With pliers, remove the air intake accessory tubes from the intake pipe.
Hands position the polished Takeda intake tube at the black coupler clamp near the throttle body in the engine bay.
View the clamp on the intake tube nearest the throttle body as accessory tubes are removed in this step.
  1. Loosen the clamp closest to the throttle body.
  2. With a pair of pliers, remove the air intake accessory tubes.

13 Remove Air Intake

Hands removing the chrome air intake tube from the Civic Si engine bay beside the red valve cover.
Once all tubes are off, lift the air intake completely out of the engine bay as shown.
Hands lift the polished Takeda intake tube with black coupler from the Civic Si engine bay.
Once tubes are off, lift the intake completely out of the engine bay as shown.
Throttle body and remaining engine bay hoses after air intake removal on 06-11 Civic Si
With the tubes already off, the air intake is fully removed, leaving the throttle body and surrounding hoses exposed.
  1. Once all of the tubes have been removed, remove the intake completely.

14 Remove Intake Hoses

Hand uses pliers on the clamp of a factory intake hose at an engine bay fitting.
Use pliers to loosen and remove the hose clamp from the factory intake hose.
Black factory hose on a T-fitting with metal clamp beside engine components in the bay.
Factory hose and clamp on the black fitting after locating the intake hose to remove for this step.
  1. Use plies to remove the hose clamp and then remove the factory hose.

15 Install new coolant line

Hand holds new upper IACV coolant hose with OEM clamps above the throttle body in the engine bay.
New upper IACV coolant hose with OEM clamps, ready to run from the throttle body IACV to the coolant housing.
Black upper IACV coolant hose fitting beside white spacer on throttle body coolant housing.
Fit the new upper IACV coolant hose to the upper section of the IACV on the throttle body coolant housing.
Hand connects new upper IACV coolant hose at the throttle body in the Civic Si engine bay.
Attach the new upper IACV coolant hose to the upper section on the throttle body, as circled.
  1. Your intake system should include a new upper IACV coolant hose. Be sure to use the OEM hose clamps.
  2. Install the line from the upper section of the IACV located on the throttle body and the coolant housing.

16 Remove Upper Radiator Hose

Hands hold the disconnected upper radiator hose beside the radiator support in the Civic Si engine bay.
Upper radiator hose removed after sliding back the clamps; note its position near the radiator support crossmember.
Pliers grip a clamp on the upper radiator hose in the Civic Si engine bay.
Slide the hose clamp back on the upper radiator hose with pliers before removing the hose.
Hands pull the upper radiator hose free from fittings in the Civic Si engine bay.
Lift the upper radiator hose free once the clamps have been slid back.
  1. Using a pair of pliers, slide the hose clamps back. Remove the upper radiator hose.

17 Install Hose Clamps

Hands hold the new upper radiator hose with a clamp slid on near the Civic Si engine bay.
Slide the clamps onto the new upper radiator hose as shown before fitting it in the engine bay.
Hands hold a black curved hose with a silver clamp slid onto one end in front of the Civic Si engine bay.
Slide the hose clamp onto the end of the new upper radiator hose as shown before installation.
  1. Slide the clamps onto the new upper radiator hose.

18 Install New Radiator Hose

Hand grips the new upper radiator hose with clamp in the Civic Si engine bay.
Install the new upper radiator hose and slide the clamps back into place on the engine.
Hands seating the new upper radiator hose with green-ring clamp onto the radiator neck under the core support.
Slide the hose fully onto the radiator neck and move the clamp back into place over the bead.
  1. Install the new upper radiator hose and slide the clamps back into place.

19 Remove Lower Hose bracket

Lower radiator hose bracket fastener circled beside the black hose in the Civic Si engine bay.
Remove the lower radiator hose bracket at the fastener highlighted in the yellow circle.
Hand holding the removed lower radiator hose bracket near the engine bay hose area.
The lower radiator hose bracket after removal, held beside the hose it previously secured.
  1. Remove the lower radiator hose bracket.

20 Remove Frame Ground

Ratchet and socket on the battery ground terminal bolt at the upper frame rail.
Use the ratchet and socket to remove the battery ground terminal from the upper frame rail.
Battery ground terminal removed from the upper frame rail beside the engine mount.
View the battery ground wire disconnected from its bolt on the upper frame rail, hanging free with the white connector visible.
  1. Remove the battery ground terminal from the upper frame rail.

21 Install New Battery Tray

Hands slide the black Hybrid Racing battery tray into the engine bay beside the battery.
Slide the HR battery tray carefully into place in the engine bay before bolting it down.
Hand threads a supplied bolt into the Hybrid Racing battery tray on the Civic Si chassis.
Thread in and tighten the supplied bolts to secure the new HR battery tray in place.
Socket and extension tighten a bolt on the right side of the black Hybrid Racing battery tray.
Use the supplied bolts to thread in and tighten the new battery tray securely in place.
  1. Slide the HR battery tray into place. Be sure to take your time.
  2. Using the supplied bolts, thread in and tighten the battery tray in place.

22 Reinstall Battery Ground

Factory clutch line bracket with white connector and mounting bolts in the Civic Si engine bay.
Locate the factory clutch line bracket bolt to remove it before reinstalling the battery ground.
Black battery ground cable terminal bolted to the chassis near the clutch line bracket on the Civic Si.
Look at the battery ground reinstalled on the chassis; ensure metal-to-metal contact at the mounting surface.
Black bracket bolted to silver chassis near white connector and ground cables in the Civic engine bay.
Battery ground reinstalled on the chassis with metal contact after the clutch line bracket bolt is removed.
  1. Remove the bolt holding the factory clutch line bracket in place.
  2. Install the battery ground. Make sure there is a proper ground surface.
  3. noteYou may need to scratch the paint to ensure metal to metal contact.

23 Install Battery

Hands lowering a black battery into the engine bay battery tray.
Lower the battery into place in the engine bay as shown.
Battery secured in the Civic Si engine bay by a black hold-down bracket across the top.
Battery installed with the upper hold-down bracket bolted in place over the top.
  1. Install your battery.
  2. noteIf you are using an aftermarket battery, some trimming of the upper battery case may be required.

24 Reinstall Battery Wiring

Hand presses the positive battery terminal onto the post with the red protective cover open on the Civic Si battery.
Install and tighten the battery positive terminal first, with the red cover open on the battery post.
Hand uses a tool to tighten the metal clamp on the black battery cable terminal post.
Tighten the reinstalled battery cable terminal clamp on the post.
  1. Install and tighten the battery positive, and then negative terminals.

25 Reinstall Overflow Tube

Hand uses a long metal tool to free a black plastic clip on the radiator support near the overflow tube.
Remove the clip next to the radiator fill neck on the radiator support before sliding the overflow tank into place.
Hands slide the white overflow tank onto the upper battery bracket beside the battery.
Slide the overflow tank onto the upper battery bracket, shown highlighted next to the battery.
Hands reinstalling the overflow tank tube onto the fitting near the upper battery bracket.
Reinstall the overflow tank tube as shown, seating it fully on the connection near the battery bracket.
  1. Remove the clip next to the radiator fill neck on the radiator support.
  2. Slide the overflow tank onto the upper battery bracket.
  3. Re-install the overflow tank tube.

26 Install MAF into the HR Housing

Screwdriver secures the black OEM MAF sensor onto the bracket of the polished HR intake tube.
Look at the screwdriver tightening the screw that mounts the OEM MAF into the HR intake chamber.
Screwdriver securing OEM MAF sensor onto Hybrid Racing intake housing held in hand.
Secure the OEM MAF sensor into the HR intake chamber using the screwdriver on the mounting screw.
  1. Remove the OEM MAF and install it into the HR intake chamber.

27 HR Intake Pre-Assembly

Black Hybrid Racing intake hoses with lime interiors, coupler, and three clamps on a workbench.
Lay out the HR intake silicone hoses, coupler, and clamps before assembling; do not fully tighten clamps yet.
Hands use a screwdriver to tighten a clamp on the black silicone intake hose during HR intake pre-assembly.
Tighten the hose clamp on the black intake pipe assembly, leaving it loose enough to adjust later.
Hybrid Racing black intake coupler clamped between silicone hoses, held in hand during pre-assembly.
Assembled HR intake with coupler and clamps in place; leave clamps loose for later adjustment.
  1. Assemble the HR intake.
  2. reminderDon't fully tighten the clamps and you may need to wiggle and adjust them.

28 Install Upper HR intake tube

Hands sliding the black Hybrid Racing upper intake tube into place in the Civic Si engine bay.
Slide the HR upper intake tube into place, checking for enough room near the fender well.
Black ribbed Hybrid Racing upper intake tube positioned in the engine bay near the fender well.
HR upper intake tube slid into place, showing clearance near the fender well.
Hand positions the Hybrid Racing upper intake tube in the Civic Si engine bay near the fender well.
Slide the upper HR intake tube into place, checking clearance near the fender well.
  1. Slide the HR intake into place. Make sure there is enough room near the fender well.

29 Connect Clamps and sensor

Hands tighten a hose clamp on the intake tube at the throttle body with a screwdriver.
Tighten the hose clamp securing the intake tube to the throttle body.
Hand tightens a hose clamp with a screwdriver on the Hybrid Racing intake tube at the throttle body.
Tighten the hose clamp that secures the intake tube after sliding it onto the throttle body.
Hands reconnect the black MAF sensor plug to the Hybrid Racing air intake tube.
Re-connect the MAF sensor to the intake after sliding it onto the throttle body.
  1. Slide the intake onto the throttle body and tighten the hose clamps.
  2. Re-connect the MAF sensor.

30 Install breather tube

Hands positioning the valve cover breather tube on the Civic Si engine near the intake pipe.
Install the valve cover breather tube by positioning and securing it on the engine as shown.
Hand points to valve cover breather tube being installed near the red valve cover on the Civic Si engine.
Point to the valve cover breather tube as it is installed and tightened on the engine.
Hand uses screwdriver to tighten clamp on valve cover breather tube near Hybrid Racing intake pipe.
Tighten the valve cover breather tube clamp with a screwdriver on the installed intake.
  1. Install and tighten the valve cover breather tube.

31 Install Vacuum hose

Hands install and position the second black vacuum hose beside the red valve cover in the Civic Si engine bay.
Install and tighten the second vacuum hose, shown here being routed and held in place near the intake tube.
Hands tighten the second vacuum hose with a screwdriver on the intake in the Civic Si engine bay.
Use a screwdriver to install and tighten the second vacuum hose on the Hybrid Racing air intake.
  1. Install and tighten the second vacuum hose.

32 Install lower bracket

Hand holds the velocity stack with yellow filter face and hose clamp under the engine bay near the lower bracket area.
Hold the velocity stack and filter in place under the intake path so the lower filter bracket can be installed before tightening the clamps.
Hand holds red conical air filter against the velocity stack under the engine bay panel.
Slide the air filter onto the velocity stack and install the filter bracket before tightening the hose clamps.
Hands hold the red conical air filter onto the velocity stack in the engine bay.
Install the air filter on the velocity stack and fit the filter bracket before tightening the hose clamps.
  1. Using the supplied hose clamps, install the air intake velocity stack and filter.
  2. Install the filter bracket before tightening the clamps.

33 Tighten Filter and bracket

Black filter bracket lined up to chassis threaded hole beside red air filter and clamp on Civic Si.
Line up the filter bracket with the threaded hole in the chassis next to the installed air filter.
Hands position the black filter bracket as a wrench tightens its bolt into the chassis threaded hole.
Tighten the bolt securing the lined-up filter bracket to the chassis threaded hole.
Hands hold a red air filter while tightening its hose clamp under the chassis bracket.
Tighten the clamp on the filter after lining the bracket up with the threaded hole in the chassis.
  1. Line up the filter bracket with the threaded hole in the chassis.
  2. noteSlight modification may be required depending on model year and coupe / sedan.

34 FlashPro Calibration

New Calibration window showing Civic Si vehicle selection, filters, and checked Show race calibrations option
In the New Calibration dialog, set Civic Si model then check Show race calibrations to list MAP-based tunes.
FlashPro New Calibration window lists AEM V2 CAI MAP-based tunes for 2006-2011 Civic Si, two rows highlighted.
In the New Calibration list, choose a MAP-based AEM V2 CAI tune such as Civic-Si-Race-6-AEMV2CAI or the RH variant.
  1. You must have a flashpro and you must upload a MAP based calibrations.
  2. These can be found under the select calibration tab when you click NEW calibration.
  3. There are a few MAP based tunes, we find the AEM V2 tunes to be sufficent in allowing the car to run properly. This IS NOT A FINAL TUNE. You should consult with a tuner and have them review your datalogs and adjust them according to your mods.
  4. cautionWe are NOT responsible for damage to your engine. DO NOT run this intake without Flashpro. DO NOT start the car unless you are confident you have selected and uploaded the correct calibration.

35 Test & Check

Hybrid Racing black intake tube installed across the 06-11 Civic Si engine bay
Fully installed Hybrid Racing cold air intake in the engine bay, ready for coolant fill and leak checks.
Hybrid Racing cold air intake tube and teal valve cover installed in the 06-11 Civic Si engine bay.
Completed intake installation in the engine bay, ready to verify no leaks once the engine reaches operating temperature.
Hybrid Racing cold air intake fully installed in the open engine bay of a Honda Civic Si.
Completed installation of the Hybrid Racing performance air intake ready for final testing and leak check.
  1. Re-install the body parts and fill the system with coolant.
  2. caution

    You must change the calibration on your Hondata Flash-Pro before cranking the engine. This intake is NOT designed to work with a MAF sensor, so upload a MAP based tune accordingly.

  3. noteMake sure the engine is up to operating temperatures and that there is no leaks.

Finishing up

Re-install the body parts and refill the coolant. Upload a MAP-based Hondata Flash-Pro calibration before starting the engine. Bring the engine to operating temperature and confirm there are no leaks.