How to install HR Short Shifter 22+ Civic Install Guide

Use this guide as a reference to install your Hybrid Racing short shifter into the 2022+ 11th Gen Civic chassis. This fits LHD models only.

Black and red Hybrid Racing short shifters with lattice bases and upright shift rods side by side.
Cover photo: assembled HR short shifters for the 22+ Civic guide, black and red finishes shown.
Difficulty
Moderate
Steps
20
Time required
30 min – 1 hr
Category
Drivetrain

Use this guide as a reference to install your Hybrid Racing short shifter into the 2022+ 11th Gen Civic chassis. This fits LHD models only.

Tools

  • Plastic Trim Tool
    Quantity: —
  • 12mm Wrench
    Quantity: —
  • Ratchet
    Quantity: —
  • 6mm Allen Socket
    Quantity: —

01 Remove Shift Knob

Two hands grip and lift the black shift knob off the center console shifter.
Begin removing the shift knob by lifting it from the center console shifter.
Hands lift the black shift knob upward off the metal shifter shaft in the center console.
Pull the shift knob straight up to remove it from the shifter shaft above the boot.
  1. Begin by removing the shift knob.

02 Remove Shift Knob

Shift knob on center console with boot collar pushed down, lock nut exposed, and removal arrows labeled.
Push the factory shift boot collar down (1), loosen the lock nut (2), then unscrew and remove the shift knob (3).
Lock nut on the shifter shaft above the boot collar in the center console, with rotation arrows.
Loosen the shift knob lock nut by turning it as indicated by the arrows.
  1. If you have an OEM shift knob:
  2. Push the factory shift boot collar downward. This will reveal the locking nut.
  3. Loosen the shift knob lock nut.
  4. Remove the shift knob.

03 Console Cover Removal

Hands use a blue plastic trim tool to unclip the upper center console cover between the front seats.
Use a plastic trim tool to gently unclip and lift the upper portion of the center console cover.
Hands lifting the upper center console cover around the shift boot on a 2022+ Civic.
Lift the unclipped upper console cover to expose the wiring and connectors underneath the shifter.
Hands hold the lifted upper console cover above the Civic center console, underside clips and wiring visible.
Lift the unclipped upper console cover to gain access to the wiring and connectors underneath.
  1. Use a plastic trim tool and unclip the upper portion of the console.
  2. There are no bolts or screws. Pull up gently and the cover will unclip.
  3. Lift the cover up to gain access to the wiring and connectors underneath.

04 Disconnect Drive Mode

Hands hold the drive mode switch panel and point to its wiring connector in the Civic center console.
Disconnect the electrical connector from the drive mode buttons and switches behind the center console.
Hand disconnects a wiring connector from the drive mode switch assembly under the Civic center console.
Disconnect the remaining drive mode switch connectors under the center console; Si trim may have several plugs.
Hand grasping black trim beside exposed wiring and shifter linkage under the Civic center console.
Disconnect the remaining drive mode button and switch connectors among the harnesses under the console.
  1. Disconnect the buttons and switches. Depending on the model, there may be 3-5 connectors. (The Si trim is shown in this guide)

05 Remove Cables

Wiring harnesses and electrical connectors at the back of the center console cover in a 2022+ Civic.
Disconnect all connectors at the rear of the console cover, including USB ports and the wireless charger if equipped.
Hands lift the center console cover from the Civic dash, exposing its underside and wiring below.
Hold the console cover tilted to access and remove USB ports and other connections on the back.
Exposed wiring harnesses, connectors, and shift linkage inside the open center console of a Civic.
Center console cover removed, revealing cables and connectors at the back to disconnect before lifting the console out.
  1. The back of the console cover holds USB ports, and other misc connections. Remove all so you can remove the console from the car.
  2. Be sure to disconnect the wireless charger (if equipped)

06 Unbolt Console

Two bolts at the bottom of the open center console armrest storage bin.
Locate the two 10mm bolts inside the armrest bin under the rubber cover, marked by the arrows.
Hands lift the cup holder section upward from the Civic center console to unclip it.
Pull upward on the cup holder section to unclip it from the console, then remove and set it aside.
Center console cavity with cup holder section removed between the front seats
Cup holder section unclipped and removed, leaving the open console cavity exposed.
  1. Inside of the arm rest, under the rubber cover, there are two 10mm bolts. Remove them.
  2. Pull upward on the cup holder section to unclip it. Remove it and set aside.

07 Unbolt Console

Two 10mm mounting bolts under the cup holders on the center console of a 2022+ Civic.
Locate and remove the two 10mm mounting bolts under the cup holders.
Hand uses a blue-handled tool on the center console under the cup holders.
Access and remove the two 10mm mounting bolts located under the cup holders in the console.
Hand holds blue screwdriver at mounting bolt under cup holder in Civic center console.
Remove the 10mm mounting bolt under the cup holders in the center console.
  1. Remove the two 10mm mounting bolts under the cup holders.

08 Unbolt Console

Two 10mm bolts on the front section of the center console, each circled in red.
Remove the two 10mm mounting bolts on the front section of the console.
Finger pointing to a gray electrical connector with wires on a black bracket inside the front console.
Arrow shows one of the two connectors inside the console to disconnect (LED light or key fob sensor).
White electrical connector with braided wire inside the front center console section.
Disconnect this connector inside the console (LED light or key fob sensor) as shown by the arrow.
  1. Remove the two 10mm mounting bolts on the front section of the console.
  2. Disconnect the two connectors inside of the console.
  3. One is an LED light, the other is the Key Fob Sensor.

09 Remove Console

Hands grip the center console between the front seats, green arrows marking its sides for removal.
Slide the loose center console backward and lift it free of the car once all wires and bolts are clear.
Center console removed between front seats, exposing the shifter assembly on the tunnel carpet.
After sliding the console backward and lifting it out, the shifter and floor tunnel are fully exposed and free of the console.
  1. Slide the console backward and remove it from the car. It should be completely loose and free of all wires and bolts.

10 Disconnect Shifter Cable

Shifter cable end and metal clip under the shifter, with inset showing clip spread and cable sliding off the ball.
Spread the metal clip (1) apart and pull it back, then slide the shifter cable end link off the ball under the shifter.
Metal clip on the shifter cable end spread apart and pulled back from the ball under the shifter.
Spread the metal clip apart and pull it back on the shifter cable end so it slides off the ball.
Hands hold the metal shifter linkage under the console, finger at the bushing by the yellow cable ball.
Finger indicates the shifter cable end after sliding it off the ball once the metal clip is pulled back.
  1. Under the shifter, you will need to remove the cable.
  2. Spread the metal clip apart and pull it back on the shifter cable end. It should slide off. Then, slide the shifter cable end link away from the shifter, seperating it from the ball.

11 Disconnect Shifter Cable

Retaining clip on the shifter cable end link at the ball stud on the shifter linkage.
Remove the retaining clip from the shifter cable end link, then slide the cable off the ball stud.
Retaining clip on the shifter cable end link attached to the black shifter assembly.
Look at the retaining clip on the shifter cable end link before removing it and sliding the cable off.
  1. Remove the retaining clip from the shifter cable end link and slide the cable off.

12 Remove Shifter Cables

Shifter cable end at the shifter with lock tab marked 1 and arrow a showing upward push to unlock.
Push the lock tab upward (1) to unlock the shifter cable before spinning the lock.
Shifter cable lock on the Civic shifter spun per curved arrows to relieve cable tension.
After unlocking, spin the cable lock (2–3) as shown to relieve tension before pushing the lock down.
Shifter cable at the short shifter with arrows showing push-back then upward pull from the groove.
Push the cable back (4), then pull upward (5) so it slides out of the groove in the shifter.
  1. Now you will need to remove the shifter cables from the shifter. This is a three-part process.
  2. 1: unlock the shifter cable by pushing the tab upwards.
  3. 2: After the cable is unlocked, spin the cable lock to relieve the tension on the cable.
  4. 3: Push the lock back down to hold it in place.
  5. 4: Push the cable back
  6. 5: Pull upward on the cable and it should slide out of the groove in the shifter.
  7. reminderRepeat this process on the other shifter cable.

13 Unbolt OEM Shifter

Two 10mm bolts securing the aluminum OEM shifter base to the chassis floor carpet.
Locate and remove these two of the four 10mm bolts holding the aluminum shifter base to the chassis.
Finger points to a bolt securing the aluminum OEM shifter base to the chassis floor.
Arrow highlights one of the four 10mm bolts holding the aluminum shifter base to the chassis; remove all four.
Finger points to a bolt securing the aluminum OEM shifter base to the chassis floor.
Red arrow marks one of the four 10mm bolts holding the aluminum shifter base to the chassis for removal.
  1. There are four 10mm bolts that hold the aluminum shifter base to the chassis.
  2. Remove all four bolts.

14 Remove OEM Shifter

Hands holding the OEM shifter assembly and base after removal from the center console area.
Remove the factory shifter assembly and shifter base from the chassis; you will not reuse this.
Removed OEM shifter assembly with cables and linkages resting on the center carpet between the front seats.
Factory shifter assembly and base removed from the chassis, with cables disconnected and lying on the floor carpet.
Red Hybrid Racing short shifter with black bracket mounted on the Civic cabin floor tunnel.
Hybrid Racing short shifter installed on the floor in place of the removed OEM shifter assembly.
  1. Remove the factory shifter assembly and shifter base from the chassis. You will not reuse this.
  2. Install the Hybrid Racing shifter using the OEM hardware.

15 Mount HR Shifter

Red Hybrid Racing short shifter mounted directly to the chassis floor in the center console area.
Hybrid Racing short shifter installed on the chassis with supplied 10mm bolts; no base bushings required.
Hands use a ratchet to tighten a bolt securing the Hybrid Racing short shifter base to the Civic chassis.
Tighten the supplied 10mm bolts to mount the Hybrid Racing shifter directly to the chassis floor.
Red Hybrid Racing short shifter bolted to the center tunnel floor between the front seats.
HR short shifter mounted directly to the chassis with the supplied 10mm bolts; no base bushings used.
  1. Use the supplied 10mm bolts and install the Hybrid Racing shifter directly to the chassis.
  2. Our shifters do not need or require base bushings.

16 Gate Spacing Adjustment

Red Hybrid Racing short shifter linkage with silver pin seated in labeled hole 1 for L/R gate spacing.
Yellow arrow marks position 1 (longest L/R throw) and green arrow marks position 2 (shortest) on the adjustable pin.
12mm wrench loosening the L/R adjustment pin on the red Hybrid Racing short shifter
Loosen the L/R gate spacing pin with a 12mm wrench before moving it to the desired position.
Red short shifter arm showing L/R gate pins in two positions with retaining clips installed.
L/R movement pins: left is Position 1 (longest/default); right is Position 2 (shortest). Tighten before install.
  1. Our shifter has two settings for F/B and L/R movements. They are independently adjustable, meaning you can do whatever combination you prefer.
  2. noteThis is the L/R movement. Adjust this pin to shorten or lengthen the left/right motion of the shifter.
  3. Position 1 is the default setting. This is the LONGEST setting possible. Approximately 15% shorter than OEM.
  4. Position 2 is the SHORTEST setting possible. This is 30% shorter than OEM.
  5. reminderTo adjust the throw, simply push the retaining clip off the backside and loosen the pin with a 12mm wrench. Unscrew the pin, place it in the desired location and retighten. Then install the clip.
  6. noteBe sure to tighten these pins before installing the shifter into your car.

17 Throw Adjustment

Red short-shifter arm with throw-adjustment pin in hole 1 and empty threaded hole 2 beside a black cage.
Throw pin in position 1 (longest); hole 2 is the shortest F/B setting—move the pin here to shorten throw.
Hand uses a wrench on the throw adjustment pin at the red arm of the Hybrid Racing short shifter.
Loosen the throw adjustment pin with a 12mm wrench after removing the retaining clip to change front/back shifter throw.
Red HR short shifter throw-adjustment arm with two pins held by retaining clips
Throw adjustment pins secured by retaining clips on the short shifter; adjust pin location before install.
  1. Our shifter has two settings for F/B and L/R movements. They are independently adjustable, meaning you can do whatever combination you prefer.
  2. noteThis is the throw adjustment. Adjust this pin to shorten or lengthen the front/back motion of the shifter.
  3. Position 1 is the default setting. This is the LONGEST setting possible. Approximately 25% shorter than OEM.
  4. Position 2 is the SHORTEST setting possible. This is 50% shorter than OEM.
  5. reminderTo adjust the throw, simply push the retaining clip off the backside and loosen the pin with a 12mm wrench. Unscrew the pin, place it in the desired location and retighten. Then install the clip.
  6. noteBe sure to tighten these pins before installing the shifter into your car.

18 Reinstall Shifter Cables

Hands guide a shifter cable onto the red Hybrid Racing short shifter assembly in the Civic center console.
Reinstall the shifter cables onto the short shifter, then install the supplied shifter offset and rod.
Hands hold a black bushing and metal pin beside the red Hybrid Racing short shifter assembly.
Install the supplied shifter offset and rod onto the short shifter as shown.
Hand holds red Hybrid Racing short shifter offset and rod above the red shifter base in the Civic cabin.
Install the supplied shifter offset and rod onto the short shifter assembly as shown.
  1. Once you have chosen your starting positions, you can reinstall the shifter cables. Follow step 12, then 11, then 10 again.
  2. Install the supplied shifter offset and rod.

19 Adjust Offset / Shift knob

Hands hold a red short-shifter offset with a silver threaded rod while a blue hex key tightens its side bolt in the Civic footwell.
Tighten the offset with a 6mm Allen so it cannot spin; set it forward (10–2) or rearward (8–4) before fitting the shift knob.
Hands hold the black shift knob while an Allen key tightens the red offset on the Hybrid Racing short shifter in the center console.
Tighten the offset with the Allen key so it cannot spin, keeping it forward or rearward while setting shift knob height.
  1. Depending on your car and shifting preference you can adjust the shift knob height and overall position.
  2. The offset must either be in the forward position (10 to 2 on a clock) or the rearward position (8 to 4 on a clock). The offset or rod will contact your console if you have it mounted to the side.
  3. cautionThese shifters DO NOT work in RHD cars. The offset WILL contact the console. If you use this in a RHD you will NOT be able to use the console cover. Please understand you will have to modify your center console if you have a RHD car. We do not recommend that.
  4. noteTighten the offset so that it does not spin. There is no set torque spec. Tighten it until it doesn't move. You may need to use a ratchet and 6mm Allen socket.

20 Install the console and drive!

Hybrid Racing short shifter installed on the center tunnel between red front seats in a Civic.
Installed short shifter ready for console reinstall after checking throw settings.
  1. Row through the gears and make sure you are comfortable with the throw settings. The shifter will wear in as you drive so it will become smoother over time.
  2. noteIf you have any questions or issues please contact our support team ASAP. Support@hybrid-racing.com
  3. Reinstall your console and go rip!

Finishing up

Row through the gears and confirm you are comfortable with the throw settings. The shifter will wear in and become smoother over time. Reinstall the console when finished.